B]BuiltZMotors is clearing out some inventory. We have one of the stage IV cylinder head packages in stock. These normally sell for $3600 (+$600 core charge) without cams. We are offering these heads at a special price of $3000 shipped anywhere in the US (+$500 core charge) or $3500 without core.[/B] (core charge refunded when we receive your cylinder heads)

$3000 shipped stage IV heads!!! BEST PRICE EVER!!!

Stage IV Head Package-WITHOUT CAMS
redeck heads - to ensure mating surfaces between the block and the heads are exact
clean parts- prep before assembly- clean oil channels, outer surface, etc.
machine heads to accept ½” head studs- will still be compatible with standard 11mm studs as well)
Full Ferrea Valvetrain:
Ferrea 1mm Oversize Intake and Exhaust Valves
Ferrea Heavy Duty Single Valve Springs
Ferrea Titanium Retainers
Ferrea Valve Spring Locators
Ferrea Valve Locks
Ferrea Valve stem seals
Ferrea valve guides
3 angle valve job: 30, 45, 60 angles on valve seat, 45 angle on valves.
Headwork-Extensive port and polish, intake, exhaust, bowl.
head assembly- valves adjusted to cams- (valve lash)
TESTING: All heads are pressure tested AND vacuum tested to insure integrity in the heads and that the valves are sealed and machined perfectly before shipped out to customer.


Exhaust ports:




Intake ports:




1mm oversized Ferrea valves:






SLEEVED BLOCK $2100...NO WAIT!!! BEST DEAL EVER!!!


An additional service that we will now offer to further aid in the reduction of a long engine build wait time is our ready to go SLEEVED shortblocks that are machined for 1/2" head studs.

Whether you would like us to machine, blueprint, and assemble your sleeved shortblock (or longblock package) or if you simply want the sleeved block for your own engine build project, we will provide the most convenient (no wait!), economical option for your vq35.



These sleeves are installed by Darton themselves. They have been decked and have been machined with timesert inserts to accept a 1/2" ARP headstud. The bare block will come with 16 ARP 1/2" studs, washers, and nuts.





PRICING:
Shipped anywhere in the US...

NEW PRICE: $2100 shipped!!! (This is less than cost!!!) +core charge

normal price: $2500 (+1000 core charge- refunded when we receive your shortblock usable core)

again... this is a bare block, machined with darton sleeves installed, machined for 1/2" head studs - use of steel insert timeserts (studs and hardware included)

NO WAIT!!! on the shelf!!!

-TODD
BuiltZMotors.com
505-480-1923

 

bump

 

would jump on it if it was an HR block
but GL with the sale

 

An HR block?? Can you clarify to the "new built motor guys" on here. Also, "GL" not sure about that one either.

 

dam this is a killer good deal!

 

"GL" is good luck .. "HR"... not really sure what the differences are... if someone else can clarify, please chime in...

 

^The new motor for the 07+

 

oh yeah, that's what they are calling it now ... not sure of the differences in the bottom end though, as in the rev up, the bottom end is interchangeable with an 03 vq

 

make me a very reasonable offer!

 

Are these heads better than the cosworth heads ?
How much more RWHP do they make over the stock head.

The price sound good.

 

comparable to the cosworth heads, these are ported and polished all by hand, by SCCH (So Cali Cyl Heads)- they do porsche and audi heads, my buddy that runs the show did about 6 sets of vq heads for me a while back..

cosworth are initially done by CNC, some have a hand finish after, some are the rough CNC finish- people can argue either way which is better...ultimately, they are very decked out, oversized valves, ferrea setup valvetrain, and meticulously ported and polished, they are an excellent head package On a forced induction setup they will make more power per pound of boost due to the increased effeciency, how much exactly is tough to say
TODD

 

PM me the cost of your basic longblock package along with a list of everything done/parts and the same for a short block package shipped to 76116 please.

 

Dr T Im loving my new motor. Ran a new Yamaha R6 from a 2nd gear roll and had him by a fender to 145. 7-0 against 600cc bikes and took my first loss to a liter bike but he traps 138 at this altitude. Can't wait to tune to high boost.

 

bump

 

Awesome prices

 

still available

 

$2000 for the sleeved block, no core charge... shipped! 1/2" head studs...man this is a great deal, someone jump on this... getting rid of some inventory!!!!

-TODD

 

ok...so I NEED to move some inventory... at $2000 this fresh unmachined sleeved darton block (sleeved by Darton) with 1/2" head studs is already below my cost....

the new super deal price is $1600 shipped!!!

pm me!!!!!!!!!!!!!!!!!

 

Dude your giving these away.

 

Wow....+1 amazing deal from a amazing long time VQ-er....very tempting.