FS: used Vq35 parts with CP pistons
#1
Registered User
Thread Starter
iTrader: (4)
Join Date: Aug 2007
Location: USA
Posts: 76
Likes: 0
Received 0 Likes
on
0 Posts
used Vq35 parts with CP pistons
Well I got my z back to stock to have these parts left over. I was holding onto these to make sure I didn't need any cores but looks like the engine in the car is running good.
All prices do not include shipping or paypal fees.
-Valve covers $150 for the pair(1 set)
-lower intake runner $25
-throttle body corner plastic fins are broken works fine $75
-coils with 29k $100
-vq35de front cover $100
-vq35 revup front and rear covers front cover is powder coated black $150
-crankshaft without marks $200 mileage 67k
-crankshaft with marks $150 29k (this is the crank that came out of car that made 750whp)
-cylinder heads with slight scratches on deck needs to be machined no valves or springs (comes with buckets and cam caps) 29k $150
-cylinder heads with 67k motor had sat outside at junkyard. rust on valves I personally go through cylinder head)$175
-vq35 revup cam gears intake and exhaust 29k $120
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
All prices do not include shipping or paypal fees.
-Valve covers $150 for the pair(1 set)
-lower intake runner $25
-throttle body corner plastic fins are broken works fine $75
-coils with 29k $100
-vq35de front cover $100
-vq35 revup front and rear covers front cover is powder coated black $150
-crankshaft without marks $200 mileage 67k
-crankshaft with marks $150 29k (this is the crank that came out of car that made 750whp)
-cylinder heads with slight scratches on deck needs to be machined no valves or springs (comes with buckets and cam caps) 29k $150
-cylinder heads with 67k motor had sat outside at junkyard. rust on valves I personally go through cylinder head)$175
-vq35 revup cam gears intake and exhaust 29k $120
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
Last edited by RB26COUPE; 12-19-2014 at 02:20 PM.
Trending Topics
#16
Registered User
Thread Starter
iTrader: (4)
Join Date: Aug 2007
Location: USA
Posts: 76
Likes: 0
Received 0 Likes
on
0 Posts
Motor was torn apart due to the head gasket on one bank was blown. Turbos needed rebuilt etc. I out the car back to stock to sell and knew I would make more money parting out than trying to sell motor as a whole. Located in Louisville, KY. Motor has bore .20 over stock but motor has less than 4k ok setup. Car made 750whp. These are all used parts
#18
Registered User
Thread Starter
iTrader: (4)
Join Date: Aug 2007
Location: USA
Posts: 76
Likes: 0
Received 0 Likes
on
0 Posts
Rods sold, no damage to heads pistons block, I bought the car that already had the work done but whomever previous owner used. Made 750whp on dynostys dyno. Motor still ran when I tore down. All the other performance parts on that engine I have already sold