anyone who loves the nismo v2 bumper please read
#62
New Member
iTrader: (13)
Fiberglass tensil strength = 3,400 (MPa) @ 2.57 (g/cm³)
Carbon weighs less, even at a lower density is stronger than fiberglass.
www.fibreglast.com
I know how to work with carbon and fiberglass, this is where I get my supplies from. You should read up on composites before you spread more misconceptions.
Last edited by mr. sparco; 07-19-2011 at 01:53 PM.
#63
New Member
iTrader: (13)
http://www.youtube.com/watch?v=pHMImrQQC5k
It pops back into place even if you step on it. It literally does, the members out there who have owned Shine products know it's very similar to OEM material. Someone stepped on my sideskirts on accident before and no crackling or damage. This is an old video and their products have gotten even better since.
It pops back into place even if you step on it. It literally does, the members out there who have owned Shine products know it's very similar to OEM material. Someone stepped on my sideskirts on accident before and no crackling or damage. This is an old video and their products have gotten even better since.
Last edited by mr. sparco; 07-19-2011 at 02:56 PM.
#64
Registered User
every carbon part ive had has been the most brittle part on my car. and i run a fiberglass front clip. i.e my CF hood is like 10 lbs. my previuos Fiberglass hood was like 16+ and much stronger than my current carbon hood. and yes they both have understructures. if the carbon hood was 16lbs it would be stronger than a 16lb fiber. but its not 16lbs.
#65
350Z-holic
iTrader: (30)
every carbon part ive had has been the most brittle part on my car. and i run a fiberglass front clip. i.e my CF hood is like 10 lbs. my previuos Fiberglass hood was like 16+ and much stronger than my current carbon hood. and yes they both have understructures. if the carbon hood was 16lbs it would be stronger than a 16lb fiber. but its not 16lbs.
and im on the forum because i recently purchased a 350z and have questions.
.
and im on the forum because i recently purchased a 350z and have questions.
.
For someone with questions you are doing a heck of alot of telling.
#66
New Member
iTrader: (13)
Flexible engine cover pieces in carbon fiber and hexal texalium. Not brittle and very strong.
Exhaust shield.
Under panel diffuser for my 350z.
These are parts I made for my own cars, I know what I'm talking about.
every carbon part ive had has been the most brittle part on my car. and i run a fiberglass front clip. i.e my CF hood is like 10 lbs. my previuos Fiberglass hood was like 16+ and much stronger than my current carbon hood. and yes they both have understructures. if the carbon hood was 16lbs it would be stronger than a 16lb fiber. but its not 16lbs.
The aftermarket "carbon" hoods out there are just 1 single layer of carbon weave, with a large amount of resin (for shine and depth, which also makes it brittle) and the rest is fiberglass for reinforcement. The only company I'm aware of that produces true carbon pieces are ASM of Japan, IE the S2000 which costs over $2k just for the hood, and Seibon who produces limited dry carbon parts over $2k per piece. I know there are more out there, but your $400 dollar brittle hood is no where near a true carbon fiber part.
Using personal experiences from cheap parts to say that carbon fiber is weaker than fiberglass is a weak argument in itself. Numbers don't lie carbon fiber is much stronger than fiberglass.
Last edited by mr. sparco; 07-19-2011 at 04:52 PM.
#68
Former Sponsor
iTrader: (564)
Join Date: Feb 2003
Location: Long Island, New York
Posts: 19,266
Likes: 0
Received 5 Likes
on
5 Posts
every carbon part ive had has been the most brittle part on my car. and i run a fiberglass front clip. i.e my CF hood is like 10 lbs. my previuos Fiberglass hood was like 16+ and much stronger than my current carbon hood. and yes they both have understructures. if the carbon hood was 16lbs it would be stronger than a 16lb fiber. but its not 16lbs.
#70
Ok just mounted my vis bumper and I have to say it fits very well with minor modification. Its dark out now but will take pictures in the morning. Gotta fill in the lines and the badge before I drop off to have painted again Friday. So if they now own wings west I do believe. They will make a quality poly piece
#72
sideskirts are just bolted from underneath so they are sagging just a tad. like i said going to be dropped off @ paint shop tomorrow morning and will look great when finished. the bumper lines up perfect. the sideskirts as well. no complaints about my vis purchase.
#78
Registered User
now dont you feel bad for trashing the quality of these bumpers already made? you made sure to let everyone know how these companies were not up to your par. i think you owe them an apology and a praise.
all these rumors about bumpers not fitting are made by paint shops when you go to get a paint estimate. they all say 'aftermarket bumpers never fit blah blah, we need to put hours of work into it blah, and we need to glass it and prime it blah. nothing but lies and crap comes out of those guys mouth. aftermarket bumpers fit great in general. they will fit unless you get very unlucky,which is rare. not the other way around. they are all quality pieces, it would be harder to make a junk part than to place something in a good mold and pop it out.
all these rumors about bumpers not fitting are made by paint shops when you go to get a paint estimate. they all say 'aftermarket bumpers never fit blah blah, we need to put hours of work into it blah, and we need to glass it and prime it blah. nothing but lies and crap comes out of those guys mouth. aftermarket bumpers fit great in general. they will fit unless you get very unlucky,which is rare. not the other way around. they are all quality pieces, it would be harder to make a junk part than to place something in a good mold and pop it out.
#79
350Z-holic
iTrader: (30)
now dont you feel bad for trashing the quality of these bumpers already made? you made sure to let everyone know how these companies were not up to your par. i think you owe them an apology and a praise.
all these rumors about bumpers not fitting are made by paint shops when you go to get a paint estimate. they all say 'aftermarket bumpers never fit blah blah, we need to put hours of work into it blah, and we need to glass it and prime it blah. nothing but lies and crap comes out of those guys mouth. aftermarket bumpers fit great in general. they will fit unless you get very unlucky,which is rare. not the other way around. they are all quality pieces, it would be harder to make a junk part than to place something in a good mold and pop it out.
all these rumors about bumpers not fitting are made by paint shops when you go to get a paint estimate. they all say 'aftermarket bumpers never fit blah blah, we need to put hours of work into it blah, and we need to glass it and prime it blah. nothing but lies and crap comes out of those guys mouth. aftermarket bumpers fit great in general. they will fit unless you get very unlucky,which is rare. not the other way around. they are all quality pieces, it would be harder to make a junk part than to place something in a good mold and pop it out.
A broken clock is right twice a day.
#80
now dont you feel bad for trashing the quality of these bumpers already made? you made sure to let everyone know how these companies were not up to your par. i think you owe them an apology and a praise.
all these rumors about bumpers not fitting are made by paint shops when you go to get a paint estimate. they all say 'aftermarket bumpers never fit blah blah, we need to put hours of work into it blah, and we need to glass it and prime it blah. nothing but lies and crap comes out of those guys mouth. aftermarket bumpers fit great in general. they will fit unless you get very unlucky,which is rare. not the other way around. they are all quality pieces, it would be harder to make a junk part than to place something in a good mold and pop it out.
all these rumors about bumpers not fitting are made by paint shops when you go to get a paint estimate. they all say 'aftermarket bumpers never fit blah blah, we need to put hours of work into it blah, and we need to glass it and prime it blah. nothing but lies and crap comes out of those guys mouth. aftermarket bumpers fit great in general. they will fit unless you get very unlucky,which is rare. not the other way around. they are all quality pieces, it would be harder to make a junk part than to place something in a good mold and pop it out.
Thread
Thread Starter
Forum
Replies
Last Post
ars88
Zs & Gs For Sale
18
04-04-2016 07:52 AM