no, and I suppose this means getting rid of the UniChip, right?

 

Just purchase an electronic boost controller like the Blitz SBC iD (mine will probably be onb ebay soon...going with the UTEC boost control).

 

Just to clarify, according to Jermaine, the Solenoid cannot pull larger than a 2 amp load.

 

Not true, the flat shift and launch control features will work perfectly no matter what type of boost control device you use. These two features are not tied together in any way.

 

2 Amps not 2V.

-Nathan
www.turboxs.com

 

So I can use an ebcs like the Blitz and somehow the UTEC can control the amount of pressure I build?????
Is it just controlling fuel and rpm's?

 

Solenoid capacity has very little to do with the solenoids ability to actually control boost. Unless you are mounting the solenoid in the trunk, the APS valve will work just fine. I’d argue that the APS valve, when paired with the UTEC would outperform almost any of the $600+ EBCs on the market.

Most of the high priced JDM twin solenoid designs available on the market are crap. Look at the pressure ratings of the Blitz unit for example. Their twin solenoid design doesn’t even come close to handling half of the pressure of our single design. Almost all of the popular boost control manufacturers would be better off just sourcing a GM boost control solenoid and sticking it in their own box rather then using their cheaply manufactured poor quality units. I dare you to open the impressive looking solenoid box that comes with some of these units. When you pay $700 and then see what they stick inside you’ll need a change of underwear. Then again, what is in your pants will look remarkably similar to the crap they stick in the box.

We use the twin solenoid design not for marketing purposes, but because it gives 2 major points of flexibility. 1. It allows us to apply boost pressure to only the top port of the waste-gate when we are trying to build boost. On very high boost cars this allows us to hold the waste-gate shut against exhaust backpressure so that insane boost levels can be achieved. On low boost cars, or traction limited cars, this allows the end user to install a lighter wage-gate spring rate and still manage to achieve their target boost. There are many reasons why someone would want to do this (traction control in lower gears for example). 2. By separating the two ports, we allow you to use a secondary pressure source to control the top port. It is not uncommon for a real drag car to have a small CO2 tank at 100+ to supply pressure to hold the top port closed on the top portion of the track. Our high pressure solenoids (120psi duty rated) can handle this abuse and with our twin solenoid design we can give these professional drag racers the boost control they desire without sacrificing the controller’s response in the lower to mid-range RPMs (or even in the lower gears…see the end of point 1).

Let’s face it EBCs make lots of money. They are the “hot ****” and everyone just has to have one. We sell what we believe to be the best EBC on the market, but if you purchase a UTEC you do not NEED it to achieve reliable and stable boost control. If you feel you have to have the hot “JDM YO!” parts, by all means put an HKS, Blitz, or Greddy boost controller on your UTEC equipped car. However, for 99% of the people on the market the UTEC’s boost control system is far superior and a much safer solution.

 

The UTEC's launch control is an RPM limit using spark or fuel control based on the way the user sets the parameters. The EBC will still limit your boost to your desired target. If you find that you are launching at the drag strip with too much boost, simply lower your launch RPM in the UTEC parameter menu. Look into the UTEC’s launch control use in the WRX market for more specifics.

-Nathan

 

When do we get to see these BCS's?????? Soon I hope.... as in next week?

Respect
JET

 

Nathan,
How does the Perrin solenoid compare with others? I was thinking of going with that sinced you guys dont have one available for us yet. Any others you recommend?

 

sweet put this on my car and toss me a few maps this is great news

 

also how much is this external switch?

 

I like the part about changing your underwear..
Nathan, I think the APS BCS is simply a GM, in which they defaced all the identifiable markings. Can you guys send me one of those BCS you guys are working on to play with,along with a map switch on me next shipment..

 

make that two sets of each

 

Sorry, the UTEC boost solenoid's will not be available next week. As soon as I have better release date I will let you guys know. I hate giving a date and then having to push it back due to some type of issue that arises.

The Perrrin solenoid will be be comparable to the GM Solenoid which is used widely. We have used it on a few customers WRX's it seems to work decently but not any better than the GM solenoid FWIW.

The UTEC remote switch retails for $79.

As soon as we are able to get a few test units out, we will ship one to you.

Thanks,

Jermaine@turboxs.com

 

Here is the solenoid Jermaine is refering to....

GM part# 1997152

It was used on the Syclone. It's doesn't have much bling factor. Price $15.69

http://www.trademotion.com/partlocat...&siteid=213815

YUCK !!!



Respect
JET

 

damn your good. How'd you find that so quick?!

-David (was still searching for the part #)

 

I have given my soul to the dark side, and have received great powers in return. Powers you can only beginn to imagine.... such as being able to search the internet much more quickly than the average person.



Respect
JET

 

Yeah not much bling here ...

 

Any one have any pictures of the external switch???