Vq engine for sale, good for 1875whp !!!
#1
Vq engine for sale, good for 1875whp !!!
I find this posted in a local forum and I don't why but I think there is something wrong here.
The listed below are the installed parts:
VQ35DE Engine plus shipping $3,700.00
Crower Forged Rod & CP Pistons 8.5:1 CR Stock Bore (Race Engineering 02/2005) $2,350.00
ARP Heads, Main & Rods Studs $600.00
TOMEI 268 duration with 10.5 mm lift Camshafts Set $1,400.00
Darton MID Block Sleeves $2,350.00
Ferrea Super Alloy Valves (F1565P) Exhaust Side 22° Flow Radial Groove +1mm $500.00
Ferrea Competition Plus Valves (F1563P) Intake Side 20° Super Flow Radial Groove +1mm $500.00
Ferrea Valve Springs Single Spring Special Alloy $440.00
Ferrea Titanium Retainers (E11058) 6mm $375.00
Ferrea Steel Valve Locks (K10069) 6mm Radial Groove $320.00
Ferrea Spring Seat Locators (SL1048) $420.00
Ferrea Copper Alloy Valve Guides (VG1041) Exhaust + .001 Over Size $500.00
Ferrea Manganese Bronze Valve Guides (VG1039) Intake + .001 Over Size $500.00
Ferrea Valve Seals (VS1012) Exhaust 6mm Valve Steam. Viton Rubber Compound. $35.00
Ferrea Valve Seals (VS1014) Intake 6mm Valve Steam. Viton Rubber Compound $35.00
Nissan Main and Rod bearings, Nissan Cam seals, Heads gasket match, Valve Stem Heights set $450.00
Combustion chamber cleanup, Block Bored and Honed using a Torque Plate $250.00
Cometic Metal Heads Gaskets, Balance Rotating Assembly, Block re-decked, Cold Clearance set $2,250.00
Ported and Polished Intake & Heads (exhaust and intake runners) with 3 angle valve job $2,250.00
Heads oil passages cleaned, Heads re-decked, Block oil passages cleaned $214.00
Tilton Carbon Triple Disk Clutch & Flywheel $4,250.00
NISMO Oil Pump $1,014.00
CJM Fuel Rails High Luster Polished $361.00
RC Injectors 1000cc without clips and 0.480" spacers - Dead time is 1.2 msec $450.00
ARP L19 11MM Head Studs $490.00
SVRT Head Lifting Fix Studs $110.00
Injected Performance Solid Engine Mount $295.00
Denso IKH20 Spark Plug 350Z (2 steps colder than stock heat range) priced per set of 6 $72.00
Parts included but not installed:
HKS DLI $580.00
SGP Racing Chromoly Pivot Ball $39.95
SFR Twin TB manifold and pipes and a TBs (With vacuum outlet) – listed below
SFR Inter Cooler 2nd outlet $4,000.00
Injected Performance VQ35DE Billet Girdle $450.00
Pathfinder cooling upgrade $275.00
All of the above cost is more than (((US$ 30,000.00))) and it’s up for sale for the highest bidder
The same engine was able to produce around (((1,875whp)))
The listed below are the installed parts:
VQ35DE Engine plus shipping $3,700.00
Crower Forged Rod & CP Pistons 8.5:1 CR Stock Bore (Race Engineering 02/2005) $2,350.00
ARP Heads, Main & Rods Studs $600.00
TOMEI 268 duration with 10.5 mm lift Camshafts Set $1,400.00
Darton MID Block Sleeves $2,350.00
Ferrea Super Alloy Valves (F1565P) Exhaust Side 22° Flow Radial Groove +1mm $500.00
Ferrea Competition Plus Valves (F1563P) Intake Side 20° Super Flow Radial Groove +1mm $500.00
Ferrea Valve Springs Single Spring Special Alloy $440.00
Ferrea Titanium Retainers (E11058) 6mm $375.00
Ferrea Steel Valve Locks (K10069) 6mm Radial Groove $320.00
Ferrea Spring Seat Locators (SL1048) $420.00
Ferrea Copper Alloy Valve Guides (VG1041) Exhaust + .001 Over Size $500.00
Ferrea Manganese Bronze Valve Guides (VG1039) Intake + .001 Over Size $500.00
Ferrea Valve Seals (VS1012) Exhaust 6mm Valve Steam. Viton Rubber Compound. $35.00
Ferrea Valve Seals (VS1014) Intake 6mm Valve Steam. Viton Rubber Compound $35.00
Nissan Main and Rod bearings, Nissan Cam seals, Heads gasket match, Valve Stem Heights set $450.00
Combustion chamber cleanup, Block Bored and Honed using a Torque Plate $250.00
Cometic Metal Heads Gaskets, Balance Rotating Assembly, Block re-decked, Cold Clearance set $2,250.00
Ported and Polished Intake & Heads (exhaust and intake runners) with 3 angle valve job $2,250.00
Heads oil passages cleaned, Heads re-decked, Block oil passages cleaned $214.00
Tilton Carbon Triple Disk Clutch & Flywheel $4,250.00
NISMO Oil Pump $1,014.00
CJM Fuel Rails High Luster Polished $361.00
RC Injectors 1000cc without clips and 0.480" spacers - Dead time is 1.2 msec $450.00
ARP L19 11MM Head Studs $490.00
SVRT Head Lifting Fix Studs $110.00
Injected Performance Solid Engine Mount $295.00
Denso IKH20 Spark Plug 350Z (2 steps colder than stock heat range) priced per set of 6 $72.00
Parts included but not installed:
HKS DLI $580.00
SGP Racing Chromoly Pivot Ball $39.95
SFR Twin TB manifold and pipes and a TBs (With vacuum outlet) – listed below
SFR Inter Cooler 2nd outlet $4,000.00
Injected Performance VQ35DE Billet Girdle $450.00
Pathfinder cooling upgrade $275.00
All of the above cost is more than (((US$ 30,000.00))) and it’s up for sale for the highest bidder
The same engine was able to produce around (((1,875whp)))
#6
Registered User
that's somethin fishy... i've got pretty much the same setup, minus a few things... the sleeves and the larger valves. so i'm excited to see it come back from the machine shop. if it makes 1/4 of this claimed power, i'll be happy!