vortech sound....
#1
New Member
Thread Starter
iTrader: (4)
Join Date: Jan 2008
Location: san diego, ca
Posts: 59
Likes: 0
Received 0 Likes
on
0 Posts
vortech sound....
so im kinda worried about how the unit sound. it runs fine good power no problems what so ever but it has a wierd sound! its kinda like a whinning noise. and i have a belt slipping somewhere that i cant figure out btw!! http://www.youtube.com/watch?v=mHJiGMJPuAs
#2
New Member
iTrader: (79)
Oh crap that sounds fatal...
I think your blower is in need for a FULL rebuild...not just the bearings and seals but also the gears...
That's what I had to get done to my blower when I sent it back to Vortech, becuase it started making this sound:
http://www.youtube.com/watch?v=fdVzmWfAi6Y
Sound familiar?
I think your blower is in need for a FULL rebuild...not just the bearings and seals but also the gears...
That's what I had to get done to my blower when I sent it back to Vortech, becuase it started making this sound:
http://www.youtube.com/watch?v=fdVzmWfAi6Y
Sound familiar?
Last edited by 350z006; 07-08-2010 at 10:48 AM.
#5
New Member
Thread Starter
iTrader: (4)
Join Date: Jan 2008
Location: san diego, ca
Posts: 59
Likes: 0
Received 0 Likes
on
0 Posts
u think so? y? i talked to the guy at 928 and he told me he has never seen the gears go bad inside any vortech. so i hope is right! i let him listen to the car over the phone and he deff said bearings are shot so ya. u notice any power gains just w/ the impeller?
#6
New Member
iTrader: (79)
You talked to Carl huh? Great guy...
Well, for your sake I hope the gears aren't involved...
As for the gains on my setup, here's my thread, but it was coupled with a built engine and other mods...
https://my350z.com/forum/forced-indu...g-results.html
However this guy below did just an impeller change, and he did got some gains...
https://my350z.com/forum/forced-indu...ller-dyno.html
Well, for your sake I hope the gears aren't involved...
As for the gains on my setup, here's my thread, but it was coupled with a built engine and other mods...
https://my350z.com/forum/forced-indu...g-results.html
However this guy below did just an impeller change, and he did got some gains...
https://my350z.com/forum/forced-indu...ller-dyno.html
#7
Registered User
iTrader: (4)
Join Date: Apr 2009
Location: Puerto Rico
Posts: 769
Likes: 0
Received 0 Likes
on
0 Posts
I don't see how the gears could go bad. My blower sounds kinda loud...not the same as the videos but similar. It's always sounded like this though and I think it sounds fine so I'll leave mine intact for the moment.
Trending Topics
#8
New Member
iTrader: (79)
BTW, this is that same blower from my video above after I got it repaired by Vortech (This is not my 928 impeller blower)
http://www.youtube.com/watch?v=8G1kKtekoZA
http://www.youtube.com/watch?v=8G1kKtekoZA
#12
Registered User
iTrader: (4)
Join Date: Apr 2009
Location: Puerto Rico
Posts: 769
Likes: 0
Received 0 Likes
on
0 Posts
BTW, this is that same blower from my video above after I got it repaired by Vortech (This is not my 928 impeller blower)
http://www.youtube.com/watch?v=8G1kKtekoZA
http://www.youtube.com/watch?v=8G1kKtekoZA
#18
New Member
iTrader: (12)
Join Date: Aug 2003
Location: Bronx N.Y/North N.J
Posts: 249
Likes: 0
Received 0 Likes
on
0 Posts
I just sent my blower back to Vortech and they told me 3-4 week turn around. It sucks it broke on the ride home from the dyno its a brand new V-3 unit and it sound just the bad ones in these video's. Has anybody put one of thes 928 impeller's into a V-3 Unit?