SVRTech 2.5" dual exhaust group buy.
Thread Starter
Registered User
iTrader: (27)
Joined: Sep 2004
Posts: 4,268
Likes: 1
From: tigard oregon
i am holding off right now on making more. i may start back up again though. it is currently getting tested by an independant shop on a new 07 versus the stock exhaust. will post up results when i hear from them. if interest is good, i will start making them again.
Registered User
Joined: Dec 2006
Posts: 362
Likes: 0
From: TN
Originally Posted by overZealous1
i am holding off right now on making more. i may start back up again though. it is currently getting tested by an independant shop on a new 07 versus the stock exhaust. will post up results when i hear from them. if interest is good, i will start making them again.
What about special orders. I am saving up for this exhaust presently. So, by the time I'm done saving, you might be producing it again. Believe me when I tell you that I am DEAD SET on this exhaust system. If you won't produce it, then perhaps you can provide me with the resources/contacts to get the components to duplicate this on my own car.
Thread Starter
Registered User
iTrader: (27)
Joined: Sep 2004
Posts: 4,268
Likes: 1
From: tigard oregon
Originally Posted by rhythmnsmoke
What about special orders. I am saving up for this exhaust presently. So, by the time I'm done saving, you might be producing it again. Believe me when I tell you that I am DEAD SET on this exhaust system. If you won't produce it, then perhaps you can provide me with the resources/contacts to get the components to duplicate this on my own car.
just stay in contact with me and we will get it worked out for ya!
Registered User
Joined: Dec 2006
Posts: 362
Likes: 0
From: TN
Originally Posted by overZealous1
what year is your car? we did find out the manifold flanges ARE different on the 07's. if a cat-back system is put on, they are the same from the cats back, though.
just stay in contact with me and we will get it worked out for ya!
just stay in contact with me and we will get it worked out for ya!
I have an 2003 Touring Edition.
Originally Posted by overZealous1
i have the design planned out, almost all the manufacturing quirks worked out too. just need to start on the prototype. think top secret!!
itb type set up with adjutable length runners. polished inside and a clear top to show it all off. it may need custom fuel rails and a custom strut bar, the measurements are so close right now it will take building one to figure it out, but shooting for a bolt on for even a stock Z. we are also going straight off the head, not the lower intake, so again a total redesign. price will not be cheap, but comparable to others. this will have alot more bling factor and there really is no way to design it better, so tq and hp gains will be maximized. with adjustable length runners, people can tune the manifold to do what they want it to do.
i hate blowing my own secrets!
i might be new to making parts for the public but i have been doing this stuff almost 20 years now, and i'm only 33, lol.
itb type set up with adjutable length runners. polished inside and a clear top to show it all off. it may need custom fuel rails and a custom strut bar, the measurements are so close right now it will take building one to figure it out, but shooting for a bolt on for even a stock Z. we are also going straight off the head, not the lower intake, so again a total redesign. price will not be cheap, but comparable to others. this will have alot more bling factor and there really is no way to design it better, so tq and hp gains will be maximized. with adjustable length runners, people can tune the manifold to do what they want it to do.
i hate blowing my own secrets!
i might be new to making parts for the public but i have been doing this stuff almost 20 years now, and i'm only 33, lol.
Thread Starter
Registered User
iTrader: (27)
Joined: Sep 2004
Posts: 4,268
Likes: 1
From: tigard oregon
Originally Posted by Pilot_Z
Is this shelved Scott?
Thread Starter
Registered User
iTrader: (27)
Joined: Sep 2004
Posts: 4,268
Likes: 1
From: tigard oregon
Originally Posted by punish_her
Scott, can you pleas PM me on price of 3" shipped to 96701. Thats if you have any available.
for right now, keep an eye in the marketplace and ya may be able to find one. thanks for the interest though.
btw- the independant shop that was going to be testing the exhaust on the new 07, got the exhaust at my cost (without including my labor!!) and never did ANY tests with it!!! said it was for their shop car and come to find out they sold it to a customer and did install. i got abit soaked on that deal and pissed off abit someone would set something up like that just to make a few extra bucks. really sucks there is not much integrity in this business.
no, they are not a forum sponsor and care not to mention their name to thus complete the cycle of the recent forum sponsor fights.
Man sorry to hear that. That realy suck! I cant imagine some peoples integrity. Either way man congrats on the good biz, a loss for us but keeps you going.
I'll definately keep my eyes open.
I'll definately keep my eyes open.
Thread Starter
Registered User
iTrader: (27)
Joined: Sep 2004
Posts: 4,268
Likes: 1
From: tigard oregon
Originally Posted by punish_her
Man sorry to hear that. That realy suck! I cant imagine some peoples integrity. Either way man congrats on the good biz, a loss for us but keeps you going.
I'll definately keep my eyes open.
I'll definately keep my eyes open.
there is a serious market for a good affordable rear diffuser and i start building mine in the next week or so! look for pics in a few weeks, prolly in the fi section.
Thread
Thread Starter
Forum
Replies
Last Post
