Aug 11th Meet. FRIDAY !! It's ABOUT TIME !!!
#81
Registered User
Thread Starter
Join Date: Mar 2004
Location: Houston, Texas
Posts: 66
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by TruBluZ
I may not be able to make it after all. I have some issues with my exhaust
Just come out and hang out with us then, bring another car, or better trailer the Z hehe
Hope you can just make it out and just hang out.
#82
Registered User
iTrader: (30)
Originally Posted by vo7848
What happened?
#83
Registered User
iTrader: (3)
Join Date: Mar 2004
Location: houston
Posts: 1,736
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by TruBluZ
Ha, wish that would work. Too bad the POS exhaust hits everything under the car. Worst exhaust EVER!!!
#84
Administrator
iTrader: (25)
Originally Posted by TruBluZ
I have always had issues with this exhaust. First it was hitting the driveshaft, then to make it work, we pushed it over to one side. This of course made it hit another part under the car. I took it to a muffler shop and had them try to fix it, but the flanges made the moving limited. Then, after the clutch install, the damn exhaust hits again. I am just fed up with the POS. I tried to contact the company about it and their response was, "ours doesn't have those issues." Guess since they have no problems, it means I shouldn't have them. Great customer service by the way. Never again will I recommend or buy something from them!
#85
Registered User
iTrader: (30)
Originally Posted by nexstage350
i thought everything got squared away already? dammmn
If all else fails, get a bigger hammer!
#87
Administrator
iTrader: (25)
Originally Posted by TruBluZ
When I beat the crap out of the piping, it will be fixed. I got under the car today, the driver's side piping is hitting the rear brace on the car. The exhaust goes over the brace and I could move the pipe enough for it to bounce off of the brace. We already put washers between the brace and the car for more clearance, but doesn't seem to be working. I think I may have it done it time.
If all else fails, get a bigger hammer!
If all else fails, get a bigger hammer!
#89
Registered User
iTrader: (30)
Originally Posted by vo7848
Have you ever thought of fabricating a small rubber bushing made of high temp resistant rubber, and placing it between the brace and the exhaust pipe?
Originally Posted by second2none
What type of exhaust is it?
#90
Administrator
iTrader: (25)
Originally Posted by TruBluZ
Yes, I thought about that. I'm going to first try to readjust it and see if I can get it to clear. Wish me luck. I may go out to the shop here at work and see what we use on our units.
#93
Registered User
iTrader: (7)
Join Date: Apr 2005
Location: My car
Posts: 790
Likes: 0
Received 0 Likes
on
0 Posts
George,
Don't know if this will help or not, but I did this to mine (pic )to prevent any contact/rattle with this certain area and it works like a charm. Kinda ghetto but it's underneathe the car, so who cares.
Don't know if this will help or not, but I did this to mine (pic )to prevent any contact/rattle with this certain area and it works like a charm. Kinda ghetto but it's underneathe the car, so who cares.
Last edited by visionboy; 08-08-2006 at 03:43 PM.
#97
Administrator
iTrader: (25)
Originally Posted by Gryphin
8pm huh, i might have to bring out my camera and snap a could shots, duuno if i will have my daily by then... but ill try and bring the z out