Don Nguyen

iTrader: (21)

Still no set time at the moment. I was going to try and make it out there in this month or next month. However, I may be going over seas at the end of this month for a month, and then as soon as I get back, I am off to the east coast for a week or two.

-Don

Don Nguyen

iTrader: (21)

This time around, I finally remembered to take some before/after pictures for you guys. It also happens to be on car that had vinyl installed on it with materials previous purchased from Sticky City. The wrong material was used/sold, and this is what happened after the owner removed it off of his car around a year or so later. You can see there was an extreme amount of adhesive left behind after removing it. The owner told me that the material was basically starting to flake off after a year or so, and when he tried to go to remove it, it was basically just coming off in such small pieces/sections that it made it extremely time consuming.

The car is a blue Subaru STI/WRX that I vinyl wrapped the roof in my 3M 1080 gloss carbon fiber material. The owner of this car came out to me from around Glendale/Pasadena/Los Angeles County area. I gave it a shot to see if I could help him get rid of this eye sore, and the results will speak for themselves.

Since the 3M 1080 scotchprint gloss carbon fiber material is quite different from the 3M di-noc carbon fiber material, I tried to take some pictures inside and outside, to show you the different effects that it has in both conditions, to give you a better idea of how it all looks and compares.

Here is the before:




Here is what I was able to do:


























-Don

donathon@gmail.com

Don Nguyen

iTrader: (21)

My first BMW F10 5 series that I've done since this model came out. I applied my gloss black vinyl wrap material to his roof. I had some requests for closer up pictures of around the sunroof and antenna areas, to squash any doubts or worries that some had regarding those two areas. As you can see, everything is done very neatly and there are no seams or exposed areas of paint there. The owner of this car was around the Inland Empire area I believe, and came out to me in Orange County to have his roof done.















-Don

donathon@gmail.com

Don Nguyen

iTrader: (21)

PMs and e-mails replied to.

-Don

Don Nguyen

iTrader: (21)

Here's a white Audi B8 that I vinyl wrapped the roof, hood, and bumper in my matte black finish/material. The owner of this car wanted to continue the theme down from the roof to the center raised section of the hood and the center section of the bumper. I thought it looked pretty cool, and it actually ended up making the car look wider. The owner of this car was in San Diego, and I happened to be down there in the area already from Orange County, so I dropped by and did some work on his car.

















-Don

donathon@gmail.com

Don Nguyen

iTrader: (21)

Lately I've been having more people steal and use my pictures as their own without my consent. So in order to both protect me and you guys too, I decided to try out a new watermark for the mean time. It is kind of distracting, so I am going to give it a test run and see if I am going to continue with it, or leave the pictures without the watermark and accept the fact that there will be some of my images stolen and used.

Either way, onto the car. I tried doing some before and after pictures, but for some reason I forgot to do it for the roof. I vinyl wrapped the roof of this gray Audi A5 in my gloss black material, smoked/tinted his tail lights and also smoked/tinted the amber area on his front headlights. I actually blacked out the chrome on the his old C300's window trim before as well. The owner of this car came to me from around the San Diego area up to me in Orange County to get the work done.

The pictures were kind of rushed, so some of them didn't turn out as well. I mainly tried focusing on taking more up close and detailed pictures this time. I wanted to show you guys that even if there is no side/roof rail, I am able to trim it perfectly straight where it ends at the sides/edge. I also did some close up of the antenna area to show that there is no paint showing around that area, which some other installers would kind of mess up on.

Let me know what you guys think about the watermark and the pictures of the car.

Before:


After:
















-Don

donathon@gmail.com

Don Nguyen

iTrader: (21)

I don't get around to posting too many pictures of tinted/smoked tail lights, so I figured I'd do so this time around. Here's pictures of a black BMW E60 M5's tail lights and head lights that I tinted/smoked with my vinyl film material. I tinted only the red portion on the rear tail lights and for the front headlights, I tinted the turn signal chrome reflector top portion only, to bring the brightness of the chrome down a bit. He was actually around in Orange County, around Lake Forest or so, which fairly close to me.

This will be a good comparison for those who are curious about how only partial parts of the tail/head lights are when tinted versus having the whole thing done.















-Don

Donathon@gmail.com

Don Nguyen

iTrader: (21)

I went through my pictures, and decided to pick this blue E46 BMW 3 series to post pictures of for today. Since I mainly end up doing work on so many white cars, it's not always easy for the non-white colored car guys get to see how it looks on other/different colors. This car was done a while back, but I believe he was from around the Huntington Beach/Orange County area. I vinyl wrapped his roof in my gloss black material and I also did his window trim in my matte black vinyl material. This will also give guys who were interested in doing both their window trim and roofs an idea of how the matte and the gloss looks together.















-Don

donathon@gmail.com

Don Nguyen

iTrader: (21)

Here are some pictures of a pewter or a sand color Mercedes Benz C230 (I believe) that I vinyl wrapped the roof in my gloss black material with, when I was up in norcal about two months ago. The sun kept coming and going that day (you can see all of the clouds in the reflections), so it made it kind of hard to take the pictures, but I did the best I could.

I will be back up in norcal probably sometime later this year, in case anyone is interested in getting some vinyl work done on their cars. PM or e-mail me.

This car is another good example of a car that is not so brightly colored, such as a white or a red car would be, but the gloss black roof is still a subtle but noticeable addition to the car.













-Don

donathon@gmail.com

metal_gear350

iTrader: (7)

When will you be available again for install in norcal

Don Nguyen

iTrader: (21)

Uncertain at the moment. I am not even in California right now, haha

-Don

Don Nguyen

iTrader: (21)

For those of you who have PMed or e-mailed me in the last couple of weeks, you may have noticed a slight delay in my responses to your questions. I am currently out of the country, and will be so until Sept 5th. However, I have already been taking appointments starting Sept 5th, for those of you who are interested in getting work done on your cars for when I am back.

Best way to contact me and reserve an appointment is through e-mail at donathon@gmail.com. Second best way would be through PM.

Thanks.

-Don

donathon@gmail.com

Don Nguyen

iTrader: (21)

I haven't posted in a while, but that's because I've been traveling over seas for the past 6 weeks or so. Either way, I am back now, and with all of the down time while flying around, I edited a lot of my back logged photos that I hadn't gotten around to editing/posting yet. I didn't notice how "strong" my watermark were in the photos while editing these, so I do apologize for that if it interferes with the pictures too much.

Anyways, here are pictures of a silver 350z that I vinyl wrapped the roof in my gloss black vinyl material. He was a local in Yorba Linda/Orange County. Even though his wheels were a matte finish, the gloss black roof still worked and looked very good on his car regardless. So these pictures will be good for those guys out there who have matte black wheels, and were deciding if they should go with a gloss or stick to a matte finish to match their wheels.

















-Don

donathon@gmail.com

Don Nguyen

iTrader: (21)

This is a white C300 that I vinyl wrapped the roof in my gloss black material a while back. I believe this car was actually from norcal and came down to me in the Orange County area to have his roof wrapped. I work on a lot of white cars, but I haven't posted pictures of one in a while, so I figured I'd throw one into the mix. White colored cars are definitely one of the best colors to get the black roofs on, due to the contrasts, if that is the style that you are looking for or like.

















-Don

donathon@gmail.com

Don Nguyen

iTrader: (21)

Here's a darker gray/gunmetal colored M45 that I vinyl wrapped the roof in my gloss black material. The owner of this car was around the Long Beach area. Even on a darker colored car, the gloss black vinyl roof actually still accents the entire the car very well. Especially on this car, with its black rims. We decided to leave the roof rails chrome, and it actually turned out looking very nice that way. It looks as if the car came like this from the factory/dealer.

It was a hot day, so don't mind the water streaks on the roof/vinyl in some of the pictures.













-Don

Donathon@gmail.com

Don Nguyen

iTrader: (21)

Here is a silver Honda Accord sedan that I vinyl wrapped the roof in my gloss black material. You may notice, I actually have already posted pictures of this car before. I originally vinyl wrapped the roof of this car about 8-12 months ago. However, the owner of this car asked me if I could also tint/smoke his tail lights. So I decided to take this time to also take pictures of his roof again, to show progress reports of how well my material holds up, after being on the car for almost a year already. You'll see in the pictures, the roof is practically perfectly smooth like paint. Everything settled in quite nicely, and the results are awesome. It even really impressed me, haha. Interestingly enough, I tinted his tail lights for him at the end if one of their eibach meets/shows, since I was already in the area.

For the tail lights, I only tinted the clear portions, and left the red parts alone.















-Don

donathon@gmail.com

Don Nguyen

iTrader: (21)

Haven't posted pictures of matte black roofs in a while, so I figure I'd post this one up. This is a white Subaru that I vinyl wrapped the roof in with my matte black material. Not a lot of cars can pull off the matte look, but I think this Subaru was able to do it fairly well. Usually you want a car that's a bit more aggressively modded/styled if you're going to go with something like a matte black roof. If not, usually other matte black accents would go well with a matte black roof as well. Typically, if you send me pictures of your car, I can determine what would look best on your car, in my opinion and based on the amount of cars I've seen or worked on. The owner of this car was out near in the Fontana area or something like that.













-Don

donathon@gmail.com

Don Nguyen

iTrader: (21)

Here is a somewhat more recent BMW E46 328i sedan that I recently did some work on. I vinyl wrapped the roof of this car in my gloss black material. I believe the owner of this car was from around the Cerritos/Long Beach area and came out to my shop in Anaheim Hills to get the vinyl wrap done for his roof. We decided to go with the gloss black to give it that panoramic look and kind of update the look of the older aging car. The roof was beginning to fade, so with the vinyl on there, it'll end up help protecting whatever is left of the paint underneath it and at the same time give the roof a new/fresh finish to look at. I wanted to post pictures of this car, to show even on a more stock looking car, a gloss black roof is still a nice mod/addition.

Before:

















Don't mind the water streaks from trying to clean the roof out in the sun/heat.


-Don

donathon@gmail.com

Don Nguyen

iTrader: (21)

Been blacking out quite a few window trims lately, to give it that shadow trim look. Here's pictures of an alpine white BMW E46 330(?) of a member on here. We decided to go with my matte black vinyl material for the window trim on his car. It matched the wheels and theme of the car fairly well. Really toned down the bright chrome, even on this alpine white E46.

Before:







After:











-Don

donathon@gmail.com

Cali-Darkness

iTrader: (35)

Hey Don, any update on when or how often you plan on making it up to NorCal to do wraps for the locals?

I have a buddy that wants to get some stuff done on his Scion XB.