What have you done for your Z today?
Oh its real loud when you romp on it, but sounds good. Just wait til you find a tunnel or something...you will grin ear to ear
The following 3 users liked this post by abarclay:
The following users liked this post:
BigBlue (05-31-2016)
6 inch cawk is my fave!
iTrader: (3)
Drove it to work, tested out the brakes twice, once on a chipmunk and another time on a squirrel... Would ruin my whole day if I killed a furry friend on my way to work... (luckily I don't live on a very busy street street because getting rear ended would also put a damper on my Tuesday)
Senior Super Moderator
MY350Z.COM
MY350Z.COM
iTrader: (13)
I washed the Z and waxed it yesterday. Felt good to get her clean again. She was pretty dirty with all the rain we've been getting.
Also installed new Z1 slotted rotors and StopTech pads for the rear wheels.
Also installed new Z1 slotted rotors and StopTech pads for the rear wheels.
The following users liked this post:
350zchad (05-31-2016)
Registered User
Registered User
iTrader: (1)
Got in 3 base line dyno pulls. No tune, still have a couple things to finish/add on.
Done on a mustang dyno. Wish I had done this before mods.
1st run 259hp/243tq
2nd run 267hp/248tq
3rd run 269hp/250tq
04 DE
-NWP throttle body
-5/16 Motordyne spacer
-Port/Polished lower plenum
-Nismo intake & JWT pop charger
-PPE long tube headers
-Motordyne xyz y-pipe (no resonator)
-JIC TI 3" midpipe
Done on a mustang dyno. Wish I had done this before mods.
1st run 259hp/243tq
2nd run 267hp/248tq
3rd run 269hp/250tq
04 DE
-NWP throttle body
-5/16 Motordyne spacer
-Port/Polished lower plenum
-Nismo intake & JWT pop charger
-PPE long tube headers
-Motordyne xyz y-pipe (no resonator)
-JIC TI 3" midpipe
Last edited by Manny00; 05-31-2016 at 12:40 PM.
New Member
Installed my NRG CF struts.
<a href="http://s638.photobucket.com/user/blufc3s/media/2007%20350Z/image_18.jpeg.html" target="_blank"><img src="http://i638.photobucket.com/albums/uu104/blufc3s/2007%20350Z/image_18.jpeg" border="0" alt=" photo image_18.jpeg"/></a>
<a href="http://s638.photobucket.com/user/blufc3s/media/2007%20350Z/image_18.jpeg.html" target="_blank"><img src="http://i638.photobucket.com/albums/uu104/blufc3s/2007%20350Z/image_18.jpeg" border="0" alt=" photo image_18.jpeg"/></a>
The following users liked this post:
BigBlue (06-01-2016)
The following users liked this post:
BigBlue (06-01-2016)
The following users liked this post:
BigBlue (06-01-2016)
Registered User
The following users liked this post:
BigBlue (06-02-2016)
I'm still interested in the wheel though as it looks slightly thinner and just all around significantly better than the Z wheel where did you get it from?
Yeah it's pretty odd seeing as my 04 G35x sedan had them but my 04 350z touring does not I only have the right hand set. I'm almost positive that the first gen z33 does not get the radio controls on any model.
I'm still interested in the wheel though as it looks slightly thinner and just all around significantly better than the Z wheel where did you get it from?
I'm still interested in the wheel though as it looks slightly thinner and just all around significantly better than the Z wheel where did you get it from?
http://www.ebay.com/itm/252349494303
Ordered it 13th April and got it 2th June.
So almost 2 months time but it was worth it tbh
Last edited by Gotserved; 06-02-2016 at 11:16 AM.
The following 3 users liked this post by Doggman9:
New Member
iTrader: (3)
the wheel is nice , i do like it alot
but after the long wait , i would be upset that the red center mark is off center by nearly an 1 "
but after the long wait , i would be upset that the red center mark is off center by nearly an 1 "
Last edited by jdmfetish; 06-03-2016 at 10:33 AM.