06 TT G35 build 2nd go around
#61
New Member
Thread Starter
Spent some time figuring the oil feeds out. My day didn't go as I planned 100%, but I managed to get them sorted. I was only able to finish the passanger side due to a fitting that snapped. I have to get a straight to finish the drivers side. I am very happy tho with how it is coming out.
[IMG]https://cimg1.ibsrv.net/gimg/my350z.com-vbulletin/2000x1504/80-
image_c6801297f92fbf31bc237f5fab7d62102c2aef73.jpeg[/IMG]
I'll post up the other side when I get the fitting and it all wrapped up.
[IMG]https://cimg1.ibsrv.net/gimg/my350z.com-vbulletin/2000x1504/80-
image_c6801297f92fbf31bc237f5fab7d62102c2aef73.jpeg[/IMG]
I'll post up the other side when I get the fitting and it all wrapped up.
#62
New Member
Thread Starter
Decided to go to shop today to tackle my valve covers. The one thing I wanted to to was the pcv. Wanted use true an fitting and wanted to run bigger then the -8an that is currently available from project Import. BTW I would never buy a thing from them!!! Total a**holes!!! So I said F it I'll do it myself. So I got a -10an to a straight with an o-ring. I drilled the pcv with and tapped it with a 7/8 tap. I also drilled out the rear of the drivers side a bit. If you look in on drivers side the opening really is that big. Did all this for when I do the catch can. Crankcase will flow better. I'm not recirculating it into the intake this time around. So when I tapped the cover I put grease on the tap to catch most of the shavings. Was pretty simple. And for 4 bucks verses 40 something with the shipping from project import. Was a no brainier. Anyway this is how it came out. Happy with it!!
#65
New Member
Thread Starter
Update: was finally able to get the plug and tap it for the factory oil psi sensor. I also sat the motor in the car so I could figure out the downpipes I need to modify. I will be doing this in Sunday so hope it's not to bad.
Here's pic of the sensor I tapped in the plug
#67
350Z-holic
iTrader: (13)
^nice!!
#68
New Member
Thread Starter
Spent all day fabing up the downpipes. Couldn't be happier with the way they came out. It's exactly what I had in my head I wanted to do. Changed over to 38mm wastegates with v-bands. Also wanted to split the downpipes for when I need to access the Trans. With this I will not have to remove the 3 bolts on the turbo that are a nightmare!!!
#69
New Member
iTrader: (4)
Looking real good! Something I have used in other builds on those really annoying turbo bolts that are impossible to get at once the motor is in the car. Stage 8 locking hardware. Its a great kit. You can get them at summit, ect.
http://www.stage8.com/perfauto.html
http://www.stage8.com/perfauto.html
#71
New Member
Thread Starter
Looking real good! Something I have used in other builds on those really annoying turbo bolts that are impossible to get at once the motor is in the car. Stage 8 locking hardware. Its a great kit. You can get them at summit, ect.
http://www.stage8.com/perfauto.html
http://www.stage8.com/perfauto.html
#72
New Member
Thread Starter
Powder coated. (WET BLACK). New age sandblasting and powder coating in Deptford nj did all my work. Work is flawless hands down. And I'm a VERY PICKY INDIVIDUAL!!! Powders are prismatic
#73
New Member
Thread Starter
Haven't really been doing to much. Been busy with work, but I did manage to get the factory psi sensor done. The other one snapped off I guess cause I was impatient and used a npt. Guess the taps threads were to deep and made the wall of the bolt thinner then it already was. My bsp tap finally arrived so I did it again and came out perfect!!
#75
New Member
Thread Starter
Yes stock plug on 05 and older. I have a 06 that has a temp sensor there. I mover stock oil psi to that location and have my aftermarket in the port where the stock use to be. I I drilled and tapped the same gallery that the stock oil psi sensor once was (now aftermarket) and running feeds off of that.
#77
New Member
Thread Starter
Moved it here
#79
New Member
Thread Starter
Got a chance to get down the garage and work on the fuel lines. Happy with them so far!! Terminated and secured. Covered them with Heat shield products heat shield. Love this product!! Highly recommend it!!
#80
New Member
Thread Starter
I do have a question and I'm hoping someone is glancing at this thread. Doesn't seem like much action on here but I'll give it a shot. Does anyone know if I can feed one fuel rail loop it to the other and return out the other side to the regulator? Trying to keep it clean and not all the tee fittings to split the feed and another tee to bring returns together to go to regulator. Hope I explained it correctly. Hopefully someone can chime in and Lmk. Thanks!!