Aggressive Wheels and Stretched Tires....Welcome
#9103
Registered User
iTrader: (9)
Join Date: Feb 2006
Location: New Orleans
Posts: 2,354
Likes: 0
Received 0 Likes
on
0 Posts
my black Z would be the one with the messed up fender pulled with the fenders cut. i personally dont think nothing is wrong with cut fenders as long as you dont plan on going with very aggressive offset. if you do go very aggressive then you will need to pull the fenders and you will run into problems since you lose the strength in you fenders. i didnt know anything about fitment at the time so i messed everything up. no worries next time you see pictures of my Z all will be fixed
#9105
Registered User
iTrader: (20)
Join Date: Feb 2007
Location: New Orleans
Posts: 1,514
Likes: 0
Received 0 Likes
on
0 Posts
If I recall correctly he once told me -6.
I FINALLY installed my SPC rear camber arms and got an alignment. I was at -4.5 but now i'm at -5 camber. All that mattered to me was making sure my toe was in spec. Even after the alignment my driver side would rub, so i went home and did some more pulling. Sadly enough I pulled to the point where my fender roller couldnt handle and broke on me. But all in all, everything is good now. I might be raising up my car because I work downtown and my work ramp is not permitting me entry... Lol. I get STUCK!
I FINALLY installed my SPC rear camber arms and got an alignment. I was at -4.5 but now i'm at -5 camber. All that mattered to me was making sure my toe was in spec. Even after the alignment my driver side would rub, so i went home and did some more pulling. Sadly enough I pulled to the point where my fender roller couldnt handle and broke on me. But all in all, everything is good now. I might be raising up my car because I work downtown and my work ramp is not permitting me entry... Lol. I get STUCK!
#9107
Registered User
iTrader: (20)
Join Date: Feb 2007
Location: New Orleans
Posts: 1,514
Likes: 0
Received 0 Likes
on
0 Posts
Oh yeah, and another thing.. When I was getting aligned, the guy let me go down to get eye level with the wheel and see how it was sitting.. OMFG, only half of my tire was touching the ground.
#9108
Registered User
Join Date: May 2009
Location: chicago,south side
Posts: 114
Likes: 0
Received 0 Likes
on
0 Posts
#9115
Senior Super Moderator
MY350Z.COM
MY350Z.COM
iTrader: (105)
#9120
i like boobies
iTrader: (12)
Join Date: Feb 2004
Location: Back in NOLA
Posts: 2,907
Likes: 0
Received 0 Likes
on
0 Posts
If I recall correctly he once told me -6.
I FINALLY installed my SPC rear camber arms and got an alignment. I was at -4.5 but now i'm at -5 camber. All that mattered to me was making sure my toe was in spec. Even after the alignment my driver side would rub, so i went home and did some more pulling. Sadly enough I pulled to the point where my fender roller couldnt handle and broke on me. But all in all, everything is good now. I might be raising up my car because I work downtown and my work ramp is not permitting me entry... Lol. I get STUCK!
I FINALLY installed my SPC rear camber arms and got an alignment. I was at -4.5 but now i'm at -5 camber. All that mattered to me was making sure my toe was in spec. Even after the alignment my driver side would rub, so i went home and did some more pulling. Sadly enough I pulled to the point where my fender roller couldnt handle and broke on me. But all in all, everything is good now. I might be raising up my car because I work downtown and my work ramp is not permitting me entry... Lol. I get STUCK!