Why Is My 03 Faster then alot of other Zs?
#61
Registered User
iTrader: (6)
Join Date: Jan 2007
Location: Fairfax, VA
Posts: 479
Likes: 0
Received 0 Likes
on
0 Posts
Not sure who the criticism is directed at, me or the OP...but as for me I completely agree the arguments! No word of mouth street race is going to prove anything, whether you are asking about why a street race amongst friends went the way it did or whether you are bragging! (not pointing fingers, purely hypothetical )
DYNO to prove the capabilities of the machine.
Trap times to prove the capabailities of the driver/drivers comfort w/ the machine.
End of Story.
As for me, I was just looking for RAW numbers and opinions as to whether people think its possible for early VQ's to have been put out of the factory differently with some being drastically different from the rest! Most dyno's that I have seen for '03's (using load base dyno's like dynojet and dynodynamics) have not put numbers anywhere close to 250whp stock! So I am just curious!
DYNO to prove the capabilities of the machine.
Trap times to prove the capabailities of the driver/drivers comfort w/ the machine.
End of Story.
As for me, I was just looking for RAW numbers and opinions as to whether people think its possible for early VQ's to have been put out of the factory differently with some being drastically different from the rest! Most dyno's that I have seen for '03's (using load base dyno's like dynojet and dynodynamics) have not put numbers anywhere close to 250whp stock! So I am just curious!
Last edited by VTMustard; 01-09-2008 at 04:10 PM.
#62
Registered User
iTrader: (6)
Join Date: Jan 2007
Location: Fairfax, VA
Posts: 479
Likes: 0
Received 0 Likes
on
0 Posts
Oooops just realized there was a bunch of new posts while I was writing my last post! My bad!
This is from my stock 05 base. Just in case anyone thinks this is due to the dyno, the stock 03 (touring 6MT) that pulled off of the same dyno, minutes before my pulls, got a 234.7 IIRC.
Its good to see another dyno up here! the '04 (not sure what trim but it M/T) that dynoed right after me, pulled ~15whp less than mine and had a fair number of bolt-ons, not to mention alot of the numbers I was seeing that day were about what expected considering their mods...but my pulls were alot higher than what I expected being stock! hmmmm weird
BTW, Z1NONLY, nice baseline numbers for the 05!
Originally Posted by Z1NONLY
This is from my stock 05 base. Just in case anyone thinks this is due to the dyno, the stock 03 (touring 6MT) that pulled off of the same dyno, minutes before my pulls, got a 234.7 IIRC.
BTW, Z1NONLY, nice baseline numbers for the 05!
Last edited by VTMustard; 01-09-2008 at 03:43 PM.
#63
New Member
iTrader: (26)
Mustard, your dyno looks more like mine than on z1nonly
http://i73.photobucket.com/albums/i2...0/IMG_0449.jpg for comparison
With Dyno Dynamics, don't they read low and then correct it so it would be like what it would be if it was on a dyno jet?
http://i73.photobucket.com/albums/i2...0/IMG_0449.jpg for comparison
With Dyno Dynamics, don't they read low and then correct it so it would be like what it would be if it was on a dyno jet?
#64
Registered User
iTrader: (6)
Join Date: Jan 2007
Location: Fairfax, VA
Posts: 479
Likes: 0
Received 0 Likes
on
0 Posts
As far I know your assumption is correct. Actually I think the shop that did your dyno, actually put a thread up a while back explaining this,
https://my350z.com/forum/showthread....+dyno+dynamics
So your Z is an 06...is it the HR and was it stock when you get these numbers (just curious cause it says MREV2 on the chart)?
https://my350z.com/forum/showthread....+dyno+dynamics
So your Z is an 06...is it the HR and was it stock when you get these numbers (just curious cause it says MREV2 on the chart)?
#65
Banned
iTrader: (21)
Join Date: Dec 2003
Location: Florida
Posts: 4,472
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by davidv
During 2003, Nissan built 12 NRT (Nissan Racing Team) motors for formula competition. Only 7 were delivered. Word is that 5 motors made their way into 350Zs headed to the United States. There is no documentation as to which 350Z got the NRT motor. You may have 1 of only 5.
#66
New Member
iTrader: (26)
Originally Posted by VTMustard
As far I know your assumption is correct. Actually I think the shop that did your dyno, actually put a thread up a while back explaining this,
https://my350z.com/forum/showthread....+dyno+dynamics
So your Z is an 06...is it the HR and was it stock when you get these numbers (just curious cause it says MREV2 on the chart)?
https://my350z.com/forum/showthread....+dyno+dynamics
So your Z is an 06...is it the HR and was it stock when you get these numbers (just curious cause it says MREV2 on the chart)?
With nismo exhaust is the redish pinkish, green is with mrev2, nismo, blue is with mrev2 and spacer and nismo. Baseline was 256, adding mrev2 258, adding spacer ontop is 263.9 I am a revup engine. Your dyno looks a lot like my baseline, more so compared to Z1NONLY dyno.
#71
Registered User
iTrader: (5)
Join Date: Apr 2007
Location: NJ
Posts: 1,172
Likes: 0
Received 0 Likes
on
0 Posts
lol I'm pretty sure this forum will have NO bearing on street racing at all. If people want to race on the street then theyre going to. By telling people not to talk about it on the forum doesnt really effect their decision.
#74
Registered User
iTrader: (12)
Originally Posted by 350z07
lets meet up...im from fresno too :]
Originally Posted by ke0ki2k
previous owner swapped in tighter gears?
#76
Registered User
Join Date: Dec 2007
Location: the islands
Posts: 873
Likes: 0
Received 0 Likes
on
0 Posts
In all seriousness. .i know what he means. .i have an 03 performance. .and i beat a lot of cars out there that i should get shitted on by.i even notice in 4th 5th and 6th gears my Z still pulls hard in all. .even in 6th. .i think im going to name em HERBY!!. . but regardless of the power does anyone have problems with after market parts fitting right?. .basically everything i buy doesn't fit right and i have to become CHIP FOOSE to make them fit on occasions. . .ex: Skunk 2 Spacer. .never fit right and always made my manifold touch my hood. .and the Kinetix V+ i had to cut away at some of the Hood Center Support beams so nothing touches. .
Last edited by DraGonAlchemist; 01-10-2008 at 04:46 AM.
#77
Registered User
iTrader: (2)
Originally Posted by b00b00
OK might sound dumb, but Do any of you have a factory freak motor??
I ran about 6 differnt 350z's, and I only lost to 1.
I ran two 2007 350z, with the HR, and beat them by a car n 1/2 everytime. Tried from digs, and rolls. Same result.
Ran, a friend 2006 Z with intake, exhaust, plenum spacers, and took him 2-3 cars, and was still pulling.
I have a 2003 Track model. All these were friendly races with friends I know. I wanted to see where my car stands.
Oh and I ran my friends 2001 Cobra. it still has 320hp, and he has intake, and exhaust. I was dead even with him.
My car is 100% stock.
Sorry if its in the wrong section.
I ran about 6 differnt 350z's, and I only lost to 1.
I ran two 2007 350z, with the HR, and beat them by a car n 1/2 everytime. Tried from digs, and rolls. Same result.
Ran, a friend 2006 Z with intake, exhaust, plenum spacers, and took him 2-3 cars, and was still pulling.
I have a 2003 Track model. All these were friendly races with friends I know. I wanted to see where my car stands.
Oh and I ran my friends 2001 Cobra. it still has 320hp, and he has intake, and exhaust. I was dead even with him.
My car is 100% stock.
Sorry if its in the wrong section.
https://my350z.com/forum/drag/233840-top-25-1-4-mile-times-for-tt-st-supercharger-nitrous-bolt-ons-stock.html
#78
Registered User
iTrader: (2)
Originally Posted by HondaKiller
I have an '03 base and i swear it is a freak of nature also. I never rule out driver error, but i have taken several Z's from '03-'05. I can't say much about the new ones since an '07 pulled on me a little in 3rd gear around 70mph. Might be my mods, might be my l33t shifting skillz
https://my350z.com/forum/showthread.php?t=233840
#79
Registered User
iTrader: (4)
My350z.com, the forum where just about everyone has a freak motor. In that case I must have one as well as I keep killing mt Z's with my stock one. The ones that do pull on me obviously have more freak of a motor than mine. It can't possibly be driver ineptitude... With today's manufacturing techniques\tolerances I doubt your car is special, you probably just don't fail at life. As for you loosing in your buddies cars against your own, you're familiar and most efficient with your car's seating/steering position.