Tired of wiring things directly onto the stock ECU harness...?
#43
Thanks for the update Mike!
Not much new to report with the parts situation. I did receive the large contacts and the rubber seals that install behind them in the connector. That may be all I see untill late summer. I did go back (again) and request more samples of these connectors, so I can build a few for those needing them now. But as of now I'm still being told that none are available. If that changes, I will report it here first!
Richard
Not much new to report with the parts situation. I did receive the large contacts and the rubber seals that install behind them in the connector. That may be all I see untill late summer. I did go back (again) and request more samples of these connectors, so I can build a few for those needing them now. But as of now I'm still being told that none are available. If that changes, I will report it here first!
Richard
#44
A case full of 1 of the 2 needed ecu connectors arrived today.
That is EIGHT weeks earlier than I was told they would get here!
All that is left is the remaining connector and the 1 remaining contact size to crimp on the wires.
That is EIGHT weeks earlier than I was told they would get here!
All that is left is the remaining connector and the 1 remaining contact size to crimp on the wires.
#46
New Member
iTrader: (2)
Join Date: Jan 2004
Location: Riyadh, SA
Posts: 1,295
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by Patch
A case full of 1 of the 2 needed ecu connectors arrived today.
That is EIGHT weeks earlier than I was told they would get here!
All that is left is the remaining connector and the 1 remaining contact size to crimp on the wires.
A case full of 1 of the 2 needed ecu connectors arrived today.
That is EIGHT weeks earlier than I was told they would get here!
All that is left is the remaining connector and the 1 remaining contact size to crimp on the wires.
Thanks,
Az
#47
AWESOME NEWS !!! Are these the levers ? or the other connector ?
*************
Mike, I received the 'other connector' . Which is a good thing since that is the one I have to go through and modify before assembling the harness together.
*************
Could you please make a group buy/pre-order list? And place me on it
Thanks,
Az
*************
Az, consider it done! You are on my list!
*************
Mike, I received the 'other connector' . Which is a good thing since that is the one I have to go through and modify before assembling the harness together.
*************
Could you please make a group buy/pre-order list? And place me on it
Thanks,
Az
*************
Az, consider it done! You are on my list!
#49
I'm still waiting on parts.
In the meantime though, I am having the tooling made to crimp the contacts, and that should be ready around the middle of Aug.
Regards,
Richard
In the meantime though, I am having the tooling made to crimp the contacts, and that should be ready around the middle of Aug.
Regards,
Richard
#50
New Member
iTrader: (2)
Join Date: Jan 2004
Location: Riyadh, SA
Posts: 1,295
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by Patch
I'm still waiting on parts.
In the meantime though, I am having the tooling made to crimp the contacts, and that should be ready around the middle of Aug.
Regards,
Richard
I'm still waiting on parts.
In the meantime though, I am having the tooling made to crimp the contacts, and that should be ready around the middle of Aug.
Regards,
Richard
Az
#51
New Member
iTrader: (2)
Join Date: Jan 2004
Location: Riyadh, SA
Posts: 1,295
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by Patch
I'm still waiting on parts.
In the meantime though, I am having the tooling made to crimp the contacts, and that should be ready around the middle of Aug.
Regards,
Richard
I'm still waiting on parts.
In the meantime though, I am having the tooling made to crimp the contacts, and that should be ready around the middle of Aug.
Regards,
Richard
#52
The tooling arrived a little early, I received the machine tooling last Friday. (8/13). I'm still waiting on the connector that mates to the ecu. In the meantime I will be cutting, stripping and crimping the wires, so I can start assembling the harnesses once the connector arrives.
I will be highlighting the Greddy emanage wiring as well as the Vortech wiring called out in their supercharger kit.
They will also have to be 3" longer than the original prototype shown earlier in this thread. That had to be done to allow the locking lever room to complete its cycle during unmating of the connectors.
I will be highlighting the Greddy emanage wiring as well as the Vortech wiring called out in their supercharger kit.
They will also have to be 3" longer than the original prototype shown earlier in this thread. That had to be done to allow the locking lever room to complete its cycle during unmating of the connectors.
#53
Registered User
Join Date: Oct 2003
Location: Sittin' Pretty the the Big D
Posts: 480
Likes: 0
Received 0 Likes
on
0 Posts
Hey Richard ....
not sure if you ever found them, but the 2 individual lever activated connectors are used on the Titans. I'd be glad to meet up with you to let you see them.
BTW, 350zSpeedRacer is now the owner of the harness ... she is testing it WITH the Vortech ... no problems from what she tells me.
not sure if you ever found them, but the 2 individual lever activated connectors are used on the Titans. I'd be glad to meet up with you to let you see them.
BTW, 350zSpeedRacer is now the owner of the harness ... she is testing it WITH the Vortech ... no problems from what she tells me.
#54
Registered User
Join Date: Aug 2003
Location: Massillon, OH
Posts: 1,612
Likes: 0
Received 0 Likes
on
0 Posts
Bump for update. it won't really help me since I've already hacked my ECU wires already, but still might be cool to have for "future" installs or removals.
#58
Registered User
Join Date: Aug 2003
Location: Massillon, OH
Posts: 1,612
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by westpak
I think he is already making them, I got one about a month ago for my install and it was a great thing to have.
I think he is already making them, I got one about a month ago for my install and it was a great thing to have.
-Chris
#60
Registered User
Join Date: Aug 2003
Location: Massillon, OH
Posts: 1,612
Likes: 0
Received 0 Likes
on
0 Posts
HOLY $HIT!!
I just went to the website and saw the crazy price they are asking! $249.00!! That's insane!! I was thinking they'd be like $50 or so $75 at the most!
Someone is smoking crack asking $249.00 for one of these things.
I can't believe that price
Hell, my eMange unit itself was only $269.
I just went to the website and saw the crazy price they are asking! $249.00!! That's insane!! I was thinking they'd be like $50 or so $75 at the most!
Someone is smoking crack asking $249.00 for one of these things.
I can't believe that price
Hell, my eMange unit itself was only $269.
Last edited by ChrisMCagle; 09-15-2004 at 12:11 PM.