Notices
Engine & Drivetrain VQ Power and Delivery

Help! ECU removal on '06's...

Thread Tools
 
Search this Thread
 
Old Oct 17, 2006 | 03:55 PM
  #1  
dingobiatch's Avatar
dingobiatch
Thread Starter
Registered User
iTrader: (3)
 
Joined: Mar 2006
Posts: 473
Likes: 0
From: Malibu, California
Default Help! ECU removal on '06's...

Trying to follow technosquare's instructions for ECU removal, but just got to the part where it says to find the clip in the cupholder.. problem is, for the '06's, there is no cupholder, its a change holder or something. What am I supposed to do at this point?

Thanks.
Reply
Old Oct 17, 2006 | 04:10 PM
  #2  
Rick06Z's Avatar
Rick06Z
Registered User
iTrader: (2)
 
Joined: Apr 2006
Posts: 204
Likes: 0
From: NA
Default

.

Last edited by Rick06Z; May 10, 2009 at 09:20 PM.
Reply
Old Oct 17, 2006 | 04:15 PM
  #3  
Wired 24/7's Avatar
Wired 24/7
Dr. Wired
Premier Member
iTrader: (2)
 
Joined: May 2005
Posts: 17,582
Likes: 9
From: San Mateo, CA
Default

Originally Posted by dingobiatch
Trying to follow technosquare's instructions for ECU removal, but just got to the part where it says to find the clip in the cupholder.. problem is, for the '06's, there is no cupholder, its a change holder or something. What am I supposed to do at this point?

Thanks.

Yeah the technosquare instructions are a bit outdated.

DON'T FORGET TO UNBOLT THE 10MM BOLT ON THE CIGARETTE LIGHTER (there was no cigarette lighter / power adaptor on the 03's)



Sorry but I have no idea about the change holder, since I have an 05. But I'm sure you'll figure it out if you stare at it long enough. Get your head down in there and poke a flashlight around...

Why don't you call technosquare or email them?
Reply
Old Oct 17, 2006 | 04:26 PM
  #4  
dingobiatch's Avatar
dingobiatch
Thread Starter
Registered User
iTrader: (3)
 
Joined: Mar 2006
Posts: 473
Likes: 0
From: Malibu, California
Default

Nooo. I'm not good at this stuff. Crappo. Someone has gotta know the answer to this one.
Reply
Old Oct 17, 2006 | 04:57 PM
  #5  
dingobiatch's Avatar
dingobiatch
Thread Starter
Registered User
iTrader: (3)
 
Joined: Mar 2006
Posts: 473
Likes: 0
From: Malibu, California
Default

Talked to technosquare, a tech ended up telling me that there is a tab that you push up in the back of the coin holder thing. Said its on the top part. Ive been trying to do it with a pretty long flathead screwdriver but it isn't working.. can't catch any tab. Can someone give me a better description of this?
Reply
Old Oct 17, 2006 | 09:34 PM
  #6  
dingobiatch's Avatar
dingobiatch
Thread Starter
Registered User
iTrader: (3)
 
Joined: Mar 2006
Posts: 473
Likes: 0
From: Malibu, California
Default

Anyone???
Reply
Old Oct 17, 2006 | 10:22 PM
  #7  
Rickdogg's Avatar
Rickdogg
Out of hiatus
Premier Member
iTrader: (234)
 
Joined: Jul 2004
Posts: 10,759
Likes: 4
From: My350z
Default

You could have been to TS already with them just plugging in through your harness on the side of ur dash. Just pullin ur chain man good luck
Reply
Old Oct 18, 2006 | 01:28 AM
  #8  
Wired 24/7's Avatar
Wired 24/7
Dr. Wired
Premier Member
iTrader: (2)
 
Joined: May 2005
Posts: 17,582
Likes: 9
From: San Mateo, CA
Default

I don't know what to tell you man, if I had time I'd roll out to wherever you are in socal, but this week I'm just too damn busy
Reply
Old Oct 18, 2006 | 08:10 AM
  #9  
97supratt's Avatar
97supratt
Registered User
iTrader: (61)
 
Joined: Nov 2004
Posts: 5,034
Likes: 3
From: Glendale California
Default

Dude, you dont need to take out the entire dash piece to remove the ecu. All you need to do is remove the 10mm bolt at the bottom and pull the plastic panel back because it is held on by clips. The coin tray thing you're talking about I got stuck on as well. I didn't even bother removing it, I had enough room to remove the ecu.
Reply
Old Oct 18, 2006 | 08:12 AM
  #10  
dingobiatch's Avatar
dingobiatch
Thread Starter
Registered User
iTrader: (3)
 
Joined: Mar 2006
Posts: 473
Likes: 0
From: Malibu, California
Default

Huh.. really?
I might try that, I'm just worried about breaking or bending something..

Hell, I might just drive down to torrance and get it tuned there, just cause I might be going home this weekend. I have to figure that one out.
Reply
Old Oct 18, 2006 | 08:14 AM
  #11  
97supratt's Avatar
97supratt
Registered User
iTrader: (61)
 
Joined: Nov 2004
Posts: 5,034
Likes: 3
From: Glendale California
Default

Originally Posted by dingobiatch
Huh.. really?
I might try that, I'm just worried about breaking or bending something..

Hell, I might just drive down to torrance and get it tuned there, just cause I might be going home this weekend. I have to figure that one out.
If you remove the 10mm at the right side of the plastic panel, the middle pops out. The only problem is the coin tray to the left, just leave it alone and work around it.
Reply
Old Oct 18, 2006 | 09:46 AM
  #12  
dingobiatch's Avatar
dingobiatch
Thread Starter
Registered User
iTrader: (3)
 
Joined: Mar 2006
Posts: 473
Likes: 0
From: Malibu, California
Default

Okay. I'll try it. Thanks man.
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Gruppe-S
Body Interior
13
May 16, 2016 10:42 PM
Depravity
Brakes & Suspension
14
Oct 1, 2015 04:49 PM
hulkout
Tuning
1
Sep 30, 2015 12:33 PM




All times are GMT -8. The time now is 09:50 PM.