FS: New Stage 4 Cyl Heads w/ Cams, New Sleeved Bare Block
#1
Sponsor
Injected Performance
Injected Performance
Thread Starter
iTrader: (15)
Join Date: Jun 2004
Location: Houston
Posts: 636
Likes: 0
Received 0 Likes
on
0 Posts
New Stage 4 Cyl Heads w/ Cams, New Sleeved Bare Block
I had a spare motor that I was building for the drag car but no longer need it so have the following parts up for sale:
Brand New Darton Sleeves installed in a low mileage block. The sleeves have been installed and decked. You will need to have the cylinders bored/honed to match the size piston you are going to use 96mm-100mm. Will also need to be align honed after studs are installed. This is all normal during an engine build (Dynosty can do so if you would like them to build it).
Normal Price $2,995 plus core charge, Selling this one for $2,000 no core needed.
Stage 4 Cylinder Heads (ready to install) with full Brian Crower Valvetrain:
Ported and Polished - 5 Angle Valve Job
+1mm Intake and Exhaust Valves
Springs and Retainer Kit
New OEM Valve Seals
Stage 3 BC Camshafts
Valve Buckets have been adjusted to Camshafts
Normal Price $4,495 plus core ($750), selling this pair for $2,800 no core required
Brand New Darton Sleeves installed in a low mileage block. The sleeves have been installed and decked. You will need to have the cylinders bored/honed to match the size piston you are going to use 96mm-100mm. Will also need to be align honed after studs are installed. This is all normal during an engine build (Dynosty can do so if you would like them to build it).
Normal Price $2,995 plus core charge, Selling this one for $2,000 no core needed.
Stage 4 Cylinder Heads (ready to install) with full Brian Crower Valvetrain:
Ported and Polished - 5 Angle Valve Job
+1mm Intake and Exhaust Valves
Springs and Retainer Kit
New OEM Valve Seals
Stage 3 BC Camshafts
Valve Buckets have been adjusted to Camshafts
Normal Price $4,495 plus core ($750), selling this pair for $2,800 no core required
#2
hatersgonnahate
iTrader: (162)
had you posted the heads a yr ago before I swapped my motor in I would have considered them. Especially for what I paid for my stage 2 cams..
BTW, have you guys heard anything more about the haltech IO box? Can wait to upgrade my setup to the IO box and while I am at it..an external map sensor.
BTW, have you guys heard anything more about the haltech IO box? Can wait to upgrade my setup to the IO box and while I am at it..an external map sensor.
#6
Sponsor
Injected Performance
Injected Performance
Thread Starter
iTrader: (15)
Join Date: Jun 2004
Location: Houston
Posts: 636
Likes: 0
Received 0 Likes
on
0 Posts
Revup Heads with BC Stage 3 Non Revup Cams. Revup Heads can be used on any VQ35DE block (model years 2003-2006) with the included block off plates. We have done this many times with excellent results.
Last edited by InjectedPerf; 08-17-2011 at 05:28 AM.
Trending Topics
#11
Sponsor
Injected Performance
Injected Performance
Thread Starter
iTrader: (15)
Join Date: Jun 2004
Location: Houston
Posts: 636
Likes: 0
Received 0 Likes
on
0 Posts
Jeff, you don't even want to know. I am selling a big race motor, double sleeved, billet bottom girdle, dry sump, L19 main studs/head studs, etc. cost over $29,000 and letting it go for less than half, never ran or anything.
Magnetti Marrelli ECU with pectel engine harness, coils, data logging, cost over $16,000, would sell for $7k. Just don't have any use for this stuff anymore.
Magnetti Marrelli ECU with pectel engine harness, coils, data logging, cost over $16,000, would sell for $7k. Just don't have any use for this stuff anymore.
#14
Sponsor
Injected Performance
Injected Performance
Thread Starter
iTrader: (15)
Join Date: Jun 2004
Location: Houston
Posts: 636
Likes: 0
Received 0 Likes
on
0 Posts
I believe it is a 3.6 or 3.7. More for higher revving. It is the same motor that VTR, Carl Stephens, etc have used in their full out drag cars. Comes with a Nismo crank, 280 cams, ported and polished heads, Ferrea valve train, cnc dry sump girdle with integrated main caps, Peterson oiling system, ATI pulley, aluminum or Carrillo rods, etc, etc.
Thread
Thread Starter
Forum
Replies
Last Post
Workshop12
Exterior & Interior
256
03-23-2020 01:45 PM