Removing driver's door switch panel
11-13-2008, 05:15 AM
#1
Registered User
Thread Starter
Join Date: Oct 2005
Location: yes
Posts: 49
Likes: 0
Received 0 Likes
on
0 Posts
Removing driver's door switch panel
I posted the question in another thread a few days ago but didn't get any replies. How do I remove the switch panel finisher trim pictured below? I ordered a new one because the old was scratched.
I appreciate the help.
I appreciate the help.
11-13-2008, 05:55 AM
#2
Registered User
iTrader: (15)
Join Date: Nov 2003
Location: Clarksville, Tennessee
Posts: 6,612
Likes: 0
Received 1 Like
on
1 Post
what the hell did you do to that?
also, there should be a circular bolt cover at the bottom of the middle piece (under what looks like foam). you pop that cover and unscrew it. the vinyl piece next to it just pops right off. once that first screw/bolt is out, the rest is pretty much straight forward.
also, there should be a circular bolt cover at the bottom of the middle piece (under what looks like foam). you pop that cover and unscrew it. the vinyl piece next to it just pops right off. once that first screw/bolt is out, the rest is pretty much straight forward.
Last edited by Z04; 11-13-2008 at 05:58 AM.
11-13-2008, 03:51 PM
#4
Registered User
Thread Starter
Join Date: Oct 2005
Location: yes
Posts: 49
Likes: 0
Received 0 Likes
on
0 Posts
what the hell did you do to that?
also, there should be a circular bolt cover at the bottom of the middle piece (under what looks like foam). you pop that cover and unscrew it. the vinyl piece next to it just pops right off. once that first screw/bolt is out, the rest is pretty much straight forward.
also, there should be a circular bolt cover at the bottom of the middle piece (under what looks like foam). you pop that cover and unscrew it. the vinyl piece next to it just pops right off. once that first screw/bolt is out, the rest is pretty much straight forward.
That pic isn't from my car... mine is actually very minor compared to the one pictured. There's a lengthy thread about the scratches in that area. The area scratches very easily, especially if you wear a wedding ring.
https://my350z.com/forum/exterior-in...scratches.html
The piece was $64.22 + shipping from courtesyparts.com. Part # 80961-Z33006 for a 2006 Z.
Trending Topics
11-16-2008, 03:51 PM
#11
Registered User
Thread Starter
Join Date: Oct 2005
Location: yes
Posts: 49
Likes: 0
Received 0 Likes
on
0 Posts
11-17-2008, 08:34 AM
#12
CF God
iTrader: (67)
Join Date: May 2004
Location: NJ
Posts: 1,578
Likes: 0
Received 0 Likes
on
0 Posts
im just about 100% sure...u pull the piece from the end towards the back of the car...there is a metal piece that keep it wedged in...i really dont think their are any screws...i looked at mine yesterday when i got in the car and there arent any.
11-19-2008, 08:04 AM
#14
CF God
iTrader: (67)
Join Date: May 2004
Location: NJ
Posts: 1,578
Likes: 0
Received 0 Likes
on
0 Posts
it hasnt changed for the 06...i have 06 panels in my 04...they just pop off on the drivers side...pass side u need to remove the door pull first then it just pops off...im positive
11-26-2008, 06:09 PM
#16
Registered User
Thread Starter
Join Date: Oct 2005
Location: yes
Posts: 49
Likes: 0
Received 0 Likes
on
0 Posts
Just wanted to add a final verdict to this thread...
I replaced the finisher trim piece tonight --- it just pops off, no screws, not on the '06 interior anyway. I used a small right angle pick and started at the end closest to the padded arm rest. Pull straight up and then work your way toward the front as there are several clips holding it in. Once it's loose you can snap off the switch assemblies. New one snaps back on.
My interior black. The first part I received from Courtesy was grey. After returning it they sent me part # 80961-CF40E which worked perfectly.
Thanks for the help.
I replaced the finisher trim piece tonight --- it just pops off, no screws, not on the '06 interior anyway. I used a small right angle pick and started at the end closest to the padded arm rest. Pull straight up and then work your way toward the front as there are several clips holding it in. Once it's loose you can snap off the switch assemblies. New one snaps back on.
My interior black. The first part I received from Courtesy was grey. After returning it they sent me part # 80961-CF40E which worked perfectly.
Thanks for the help.
11-28-2008, 05:46 AM
#19
Registered User
iTrader: (15)
Join Date: Nov 2003
Location: Clarksville, Tennessee
Posts: 6,612
Likes: 0
Received 1 Like
on
1 Post
hmm, now i got to go out and look at mine again, i could have sworn that you had to loosen a screw/bolt to take the whole switch cover out. i knew the padded piece just pops right out.
even this site shows the screw i was talking about (step 2)
http://liljerk.morpheus.net/350Z/front_speakers/
but then again, it could be different in a 06+
even this site shows the screw i was talking about (step 2)
http://liljerk.morpheus.net/350Z/front_speakers/
but then again, it could be different in a 06+
Last edited by Z04; 11-28-2008 at 05:48 AM.
04-04-2013, 04:57 PM
#20
Registered User
Thank you for the posts. I have the exact same scratches on my armrest and the other plastic parts in the interior. Apparently there was a defect in the paint and it didn't bind correctly. It appears to be in the 06's. Anyway, Im wrapping my parts in 3m vinyl wrap and needed to know how to remove the armrests. thank you