I need help installing new C-West side skirts
#1
Registered User
Thread Starter
iTrader: (14)
Join Date: Jun 2002
Location: Overland Park, Kansas
Posts: 633
Likes: 0
Received 0 Likes
on
0 Posts
I need help installing new C-West side skirts
I just got my C-West side skirts today and I took off my oem skirts. The oem skirts have little pop tabs but the c-west only has a few holes pre-drilled. My questions are:
1.) How would I go about making tabs similar to oem.
2.) Do I "really" need to use tabs or can I just use screws?
3.) Could I use 3M tape and screws instead?
Suggestions and advice appreciated!!
p.s. Local body shop was going to charge me for an hour of labor to take off the OEM skirts! It took me maybe 25 minutes and I've never taken side skirts off before and they supposedly have 10 years of experience!! What BS! It would probably take then half the time it took me.
1.) How would I go about making tabs similar to oem.
2.) Do I "really" need to use tabs or can I just use screws?
3.) Could I use 3M tape and screws instead?
Suggestions and advice appreciated!!
p.s. Local body shop was going to charge me for an hour of labor to take off the OEM skirts! It took me maybe 25 minutes and I've never taken side skirts off before and they supposedly have 10 years of experience!! What BS! It would probably take then half the time it took me.
Last edited by koolzero; 12-17-2003 at 08:37 PM.
#2
did you get the instructions in English? I have the instructions and could provide some guidance if you got them in Japanese.. mine were installed per the instructions and no problems with them so far..
Last edited by ether; 12-18-2003 at 06:12 AM.
#4
Dubby, check out this thread i posted some pics there. https://my350z.com/forum/showthread....threadid=52263
#6
Registered User
iTrader: (1)
If you're talking about the white tab that is afixed to the OEM skirt, you can do without it. It would be a pain to fabricate. Btw, those tabs will snap off when you remove the skirt if you're not careful.
There are so many bolts, it's not going to make much difference but perhaps you can use the tabs that came with the OEM skirt.
If you're talking about the black pop tabs, use the OEM bpts when installing the CWest. Took me 20 minutes how to stick those suckers in properly. Duh!
There are so many bolts, it's not going to make much difference but perhaps you can use the tabs that came with the OEM skirt.
If you're talking about the black pop tabs, use the OEM bpts when installing the CWest. Took me 20 minutes how to stick those suckers in properly. Duh!
#7
Registered User
Thread Starter
iTrader: (14)
Join Date: Jun 2002
Location: Overland Park, Kansas
Posts: 633
Likes: 0
Received 0 Likes
on
0 Posts
Yeah I broke a few of the white ones taking off the oem. On the c-west skirts it has 2 holes drilled in the top portion close to the kick plates. Did you use bolts there or the black pop tabs?
Trending Topics
#8
Registered User
Thread Starter
iTrader: (14)
Join Date: Jun 2002
Location: Overland Park, Kansas
Posts: 633
Likes: 0
Received 0 Likes
on
0 Posts
Oh and what is the price you guys have paid to have them painted; that is if you didn't get carbon fiber. I sort of wish that I did now but a little bit more than I wanted to spend. Espically now sinced I just bought a Nismo wing...
#9
Registered User
iTrader: (1)
Originally posted by koolzero
Yeah I broke a few of the white ones taking off the oem. On the c-west skirts it has 2 holes drilled in the top portion close to the kick plates. Did you use bolts there or the black pop tabs?
Yeah I broke a few of the white ones taking off the oem. On the c-west skirts it has 2 holes drilled in the top portion close to the kick plates. Did you use bolts there or the black pop tabs?
#11
Registered User
Thread Starter
iTrader: (14)
Join Date: Jun 2002
Location: Overland Park, Kansas
Posts: 633
Likes: 0
Received 0 Likes
on
0 Posts
What kind and size of screws do they want you to use for the two closest to the kick plates?
BTW looks like a piece of cake.
Oh and I have to drill holes for those 2 screws correct?
BTW looks like a piece of cake.
Oh and I have to drill holes for those 2 screws correct?
Last edited by koolzero; 12-18-2003 at 04:46 PM.
#12
Registered User
Join Date: Feb 2003
Location: brooklyn ny(rutgers college)
Posts: 2,788
Likes: 0
Received 0 Likes
on
0 Posts
unless it is evident that the side skirt will not hold on with the holes that are already drilled, then you dont really need to drill more holes..it will hold fine with that many holes and some 3m
#13
Registered User
Thread Starter
iTrader: (14)
Join Date: Jun 2002
Location: Overland Park, Kansas
Posts: 633
Likes: 0
Received 0 Likes
on
0 Posts
it looks like i have to drill 2 holes to attach the top portion of the skirts. If I do that with 3m tape then it will be pretty solid. Where can I get some 3m tape, does Home Depot have it?
#14
Registered User
Thread Starter
iTrader: (14)
Join Date: Jun 2002
Location: Overland Park, Kansas
Posts: 633
Likes: 0
Received 0 Likes
on
0 Posts
Man these looks sweet in black I should have gotten carbon fiber
I need to drill here. Instead of using a screw here I could probably use a bpt. What do you think?
I need to drill here. Instead of using a screw here I could probably use a bpt. What do you think?
Last edited by koolzero; 12-18-2003 at 08:02 PM.
#17
Ether...you car looks hot! very clean, the only thing is that its black and black cars make it hard to see the details of the kit...nevertheless I like it alot and the rims flow really well with the body what size r they and tire with too?
does anyone have a full cwest n1 body kit?
does anyone have a full cwest n1 body kit?
#18
Registered User
Thread Starter
iTrader: (14)
Join Date: Jun 2002
Location: Overland Park, Kansas
Posts: 633
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by Dubby
Ether...you car looks hot! very clean, the only thing is that its black and black cars make it hard to see the details of the kit...nevertheless I like it alot and the rims flow really well with the body what size r they and tire with too?
does anyone have a full cwest n1 body kit?
Ether...you car looks hot! very clean, the only thing is that its black and black cars make it hard to see the details of the kit...nevertheless I like it alot and the rims flow really well with the body what size r they and tire with too?
does anyone have a full cwest n1 body kit?