Roll Cage for 350Z Coupe ???
07-25-2004, 03:09 PM
#1
Registered User
Thread Starter
Join Date: May 2004
Location: Roadcourses of SoCal
Posts: 331
Likes: 0
Received 0 Likes
on
0 Posts
Roll Cage for 350Z Coupe ???
I would like to install a roll cage in my 2003 Track model for racetrack use. But I want to be able to leave the passenger seat in the car for street use.
Does anyone know where I can go for that kind of roll cage? Thanks.
Does anyone know where I can go for that kind of roll cage? Thanks.
07-26-2004, 01:35 AM
#2
Registered User
Join Date: Jun 2004
Location: Cali
Posts: 896
Likes: 0
Received 0 Likes
on
0 Posts
You can get a custom rollcage made.....I know Cusco makes rollcages for the IS where you can leave the passenger seat still in...Not sure is Cusco makes rollcages for the Z though....
07-26-2004, 09:35 AM
#4
Registered User
iTrader: (3)
Join Date: Jan 2003
Location: Irvine, CA
Posts: 1,426
Likes: 0
Received 0 Likes
on
0 Posts
It all depends on what you are looking to do. In my semi-cage, I have door bars which extend from the main hoop down to the footwells on each side.
You can see pics of my bar/cage by Clicking Here
You can have any bars clevis mounted for easy removal. You should be warned, the door bar does hit my elbow on turns...the ONLY way to avoid this is to gut the inner door panels as our door panels are thick with plastic.
If you're talking a full cage with A-Pillar bars then you will most likely have to also make a full race dashboard.
My cage was fabricated at Bullet Fabrication (http://www.bulletfab.com) in Gardena, CA. Mike at Bullet made my cage per SCCA specs using 4130 chromoly. He will fabricate according to whatever specs you provide him...he also designs the cage custom for you taking into account your seat position, your shoulder position and elbow position. He will be gone for the month of August for travel (guy works 7 days a week so he will be traveling for a well deserved break) but you may want to talk to him ahead of time. Good Luck.
You can see pics of my bar/cage by Clicking Here
You can have any bars clevis mounted for easy removal. You should be warned, the door bar does hit my elbow on turns...the ONLY way to avoid this is to gut the inner door panels as our door panels are thick with plastic.
If you're talking a full cage with A-Pillar bars then you will most likely have to also make a full race dashboard.
My cage was fabricated at Bullet Fabrication (http://www.bulletfab.com) in Gardena, CA. Mike at Bullet made my cage per SCCA specs using 4130 chromoly. He will fabricate according to whatever specs you provide him...he also designs the cage custom for you taking into account your seat position, your shoulder position and elbow position. He will be gone for the month of August for travel (guy works 7 days a week so he will be traveling for a well deserved break) but you may want to talk to him ahead of time. Good Luck.
07-29-2004, 07:46 AM
#7
Registered User
iTrader: (3)
Join Date: Jan 2003
Location: Irvine, CA
Posts: 1,426
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by 350ed
jimster716, if you don't mind saying via post or pm, how much did it cost you?
jimster716, if you don't mind saying via post or pm, how much did it cost you?
I really couldn't tell you how much he would charge so try calling him and asking. Let him know that Jim referred you.
Thread
Thread Starter
Forum
Replies
Last Post
Justin100
Intake Exhaust
26
11-29-2015 03:58 PM
hardkicks
Zs & Gs For Sale
0
09-20-2015 12:28 PM
