Help with HKS DLI!!!!!!!!!!
05-09-2006, 10:08 PM
#1
Registered User
Thread Starter
iTrader: (6)
Join Date: Aug 2005
Location: PHOENIX
Posts: 388
Likes: 0
Received 0 Likes
on
0 Posts
Help with HKS DLI!!!!!!!!!!
I have tried two different HKS DLI's and the car will not start, but as soon as I take it off the car starts. The car will crank but not turn over, the light to the unit shows power. We have checked all the coil-packs, grounds, and fuses.
I am running the e-manage ultimate, could this have anything to do with it?
Please help!!!!!!!!
I am running the e-manage ultimate, could this have anything to do with it?
Please help!!!!!!!!
05-09-2006, 10:40 PM
#3
Registered User
Thread Starter
iTrader: (6)
Join Date: Aug 2005
Location: PHOENIX
Posts: 388
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by mistaboosta
plug off the e-manage and retry?
btw is it DLI-I or DLI-II ?
DLI-I has known problems with certain cars like EVO etc.
btw is it DLI-I or DLI-II ?
DLI-I has known problems with certain cars like EVO etc.
I have the DLI-II
05-10-2006, 12:04 PM
#6
Thats weird I have a UTEC and it works fine. If your getting the light to come on the ground is likely good. Are you making sure the wires arent mixed up tp where they need to be? Are you sure you've fully clippped in all the ends? Where did you mount your DLI-II box and what way did you run the wiring loom-behind th eplenum or across the front with the stock harness?
Trending Topics
05-10-2006, 01:34 PM
#10
Registered User
Join Date: Nov 2005
Location: Orlando, FL
Posts: 67
Likes: 0
Received 0 Likes
on
0 Posts
Didn't one member say they had to isolate the unit from the chassis to get the VQ to start up? Put plastic / rubber washers between the unit to make it stand off from your mounting location....
Something to try..
Something to try..
05-10-2006, 04:13 PM
#15
Registered User
Join Date: Nov 2005
Location: Orlando, FL
Posts: 67
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Velicos
Didn't one member say they had to isolate the unit from the chassis to get the VQ to start up? Put plastic / rubber washers between the unit to make it stand off from your mounting location....
Something to try..
Something to try..
Post #16
Originally Posted by Alius_G
Just installed mine today. It's alot easier to disconnect the plugs while their warm. In addition, initially I had the DLI chassis touching the car chassis and it didn't start the car. Once, I isolated it worked fine. Haven't really tested it since it's midnight already..
05-10-2006, 04:19 PM
#16
have you tried disconnecting the emanage ultimate and starting it with the HKS? I'm not sure what injectors you're using or if the car would even start normally without the EU anyway, but just an idea
guess i'm wondering if the EU works fine without the HKS and the HKS works fine without the EU, but them together don't
guess i'm wondering if the EU works fine without the HKS and the HKS works fine without the EU, but them together don't
05-10-2006, 05:24 PM
#17
Registered User
Thread Starter
iTrader: (6)
Join Date: Aug 2005
Location: PHOENIX
Posts: 388
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by William@Altered
hey we are going to give you a call to ensure that it's installed right - we will walk you through it -
I think it might have something to do with the original ECU, or the E-Manage. The original ECU still has the turbonetis reflash, and I think that with the E-Manage the signal to fire the car is too weak.
The whole reason that I am putting the unit on the car is that it will not make power over 5000 RPM. When I get to 5000 RPMs under heavy load the car starts to stutter, and you can smell gas, the car will also do this when I down shift on the highway. I think that at 5000 RPMs I am just blowing out the spark on the plugs, so this is why I am trying to use this unit.
The setup that I have is
ECU with the turbonetics reflash
E-Manage Ultimate
Blitz SBC boost controller
750cc injectors
AAM fuel return system
Built motor
8.5.1 pistons
JIC full 3 inch single exhaust
I am running 15 pounds of boost, and on the dyno the boost holds through the rpms, and I have an A/F of 11.2.
Sorry for the long post, just thought that I would give a little more info.
05-10-2006, 07:06 PM
#19
Registered User
Thread Starter
iTrader: (6)
Join Date: Aug 2005
Location: PHOENIX
Posts: 388
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Alberto
Good luck with everything, I also have a TN flash and this unit with no issues. Keep us updated on your situation-btw nice mods list man sounds like a beast....
thanks, but that is only half the list.
I will let you know what I found out.