Haltech Platinum Review w/dyno numbers!
11-29-2007, 03:27 PM
#42
Registered User
Thread Starter
iTrader: (2)
Join Date: May 2004
Location: Maryland
Posts: 149
Likes: 0
Received 0 Likes
on
0 Posts
New Tune
Got a chance to do some more tuning tonight. I think I have the VTC mapped out pretty well now, it picked up a good bit of torque at the same boost level.
11-29-2007, 03:58 PM
#43
Banned
iTrader: (28)
Join Date: Dec 2005
Location: Spotswood NJ
Posts: 5,510
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by ForcefedZ
Got a chance to do some more tuning tonight. I think I have the VTC mapped out pretty well now, it picked up a good bit of torque at the same boost level.
11-29-2007, 05:23 PM
#44
Registered User
Thread Starter
iTrader: (2)
Join Date: May 2004
Location: Maryland
Posts: 149
Likes: 0
Received 0 Likes
on
0 Posts
The little turbos that could...
Well, I'm finished for the night. 699rwhp was all she had (696 uncorrected) It should break 700rwhp mark with the stock greddy turbos on an open deck block once I address a few other things. 
The graphs are in speed because the clutch will not hold the torque. Pretty good numbers for pretty basic setup
The graphs are in speed because the clutch will not hold the torque. Pretty good numbers for pretty basic setup
11-29-2007, 07:24 PM
#46
Registered User
Thread Starter
iTrader: (2)
Join Date: May 2004
Location: Maryland
Posts: 149
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Hal@IP
Incredible numbers Ray. What RPM were you turning on those?
11-30-2007, 04:33 AM
#50
Registered User
Thread Starter
iTrader: (2)
Join Date: May 2004
Location: Maryland
Posts: 149
Likes: 0
Received 0 Likes
on
0 Posts
Here is what the graph should look like once I address the clutch. The calculation are based off of 12.5ftlbs of toruque increase per pound of boost.
Torque @ 9.57psi=448rwtq
Torque @ 27.0psi should be in the 660-670 range (12.5x17.5)+448=666.75
Does anybody have some high boost graphs running the stock Greddy 18g?
Torque @ 9.57psi=448rwtq
Torque @ 27.0psi should be in the 660-670 range (12.5x17.5)+448=666.75
Does anybody have some high boost graphs running the stock Greddy 18g?
11-30-2007, 09:37 AM
#51
Got Track!!!!!
iTrader: (40)
Join Date: May 2005
Location: Fayetteville, NC
Posts: 3,307
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by ForcefedZ
Here is what the graph should look like once I address the clutch. The calculation are based off of 12.5ftlbs of toruque increase per pound of boost.
Torque @ 9.57psi=448rwtq
Torque @ 27.0psi should be in the 660-670 range (12.5x17.5)+448=666.75
Does anybody have some high boost graphs running the stock Greddy 18g?
Torque @ 9.57psi=448rwtq
Torque @ 27.0psi should be in the 660-670 range (12.5x17.5)+448=666.75
Does anybody have some high boost graphs running the stock Greddy 18g?
Wow! insane tune.
almost 700 rwtq
Thread
Thread Starter
Forum
Replies
Last Post
Lt_Ballzacki
Brakes & Suspension
39
08-06-2021 06:19 AM
