Greddy Turbo Rebuild
01-05-2009, 11:34 PM
#22
Every time I think I have chased away all the demons something else pops up. I've devoted too much time and money to this. I can't afford to pay over $1000 for a track day and only have the car make it 1/4 way through it.
I need to solve the crankcase pressure issue and the turbo's won't leak anymore.
I need to solve the crankcase pressure issue and the turbo's won't leak anymore.
01-06-2009, 06:13 AM
#25
Every time I think I have chased away all the demons something else pops up. I've devoted too much time and money to this. I can't afford to pay over $1000 for a track day and only have the car make it 1/4 way through it.
I need to solve the crankcase pressure issue and the turbo's won't leak anymore.
I need to solve the crankcase pressure issue and the turbo's won't leak anymore.
That sucks bro..bummer..ironically enough my Z is setup very close to what you had suggested, the only difference being that the drivers side is not "drilled out". I still have the freaking coolant pressurization issue and just picked up a "combustion gas in the coolant tester". I think I will try another new greddy or toyo high pressure cap, buy a nismo low temp thermo and see what it does then. I can cruise around all day long not going into boost and have no issues, if I beat on it then the overflow fills up and the car will eventually overheat because of an "airlock" situation. I've been ready to pull my hair out with this crap..but take a deep breath and keep working the issue. Think how good its going to feel when you get the issue resolved and you can run the crap out of it at the track! You're on the leading edge of this with as much HP as you're making..so don't give up..stay after it!
06-23-2009, 10:12 AM
#30
Registered User
iTrader: (8)
Join Date: Apr 2006
Location: South FLA
Posts: 1,413
Likes: 0
Received 0 Likes
on
0 Posts
i just went to the site for Forced Perfomance..says there out of Texas, but a earlier post says florida.. need to get mine rebuilt possibly
Last edited by IslandZavage; 06-23-2009 at 10:22 AM.
06-24-2009, 06:26 AM
#31
http://www.blouchturbo.com/upgrades/
At least you can compare costs this way. BTW, the turn time on my upgrade was amazing. Good luck.
06-24-2009, 08:01 AM
#32
Run valve cover breather vents into your exhaust after the turbo. See it at the drag strip all the time with high compression v8s. The exhaust will keep it in someone what of a vacum. You need to take a small pipe and angle it into the exhaust pipe, facing the rear of the car, at an angle. This way the exhaust will draw pressure out of the crank case.
Link with pictures to give you an idea.
http://www.teglerizer.com/triumphstu...scavenging.htm
Jegs has the kit you need.
http://www.jegs.com/i/Moroso/710/25900/10002/-1 60$
Link with pictures to give you an idea.
http://www.teglerizer.com/triumphstu...scavenging.htm
Jegs has the kit you need.
http://www.jegs.com/i/Moroso/710/25900/10002/-1 60$
Last edited by rocks; 06-24-2009 at 08:06 AM.
Thread
Thread Starter
Forum
Replies
Last Post
350Z_Al
Exterior & Interior
133
10-29-2020 07:44 PM
300zx, cost, crankcase, florida, greddy, illinois, kit, leak, parts, rebuild, rebuilders, rebuilding, replacement, turbo, venting
