My FI story
the shroud has room. Not mutch but enough.
03-26-2011, 03:38 PM
#45
Registered User
Thread Starter
Join Date: Dec 2007
Location: Netherlands
Posts: 209
Likes: 0
Received 0 Likes
on
0 Posts
Little Update.
I installed the APS Extreame rail incl. The 880 injectors..
First the brackets.
Tacking out the injectors and putting some grease on it to install it.
Fitting the injectors in the rail.
Pushing the rail in place.
And now the exhaust for the turbo.
Adding the turbo's
The upgraded oilfeed lines from GTM
Next the oil return piping.
keep You Updated..
I installed the APS Extreame rail incl. The 880 injectors..
First the brackets.
Tacking out the injectors and putting some grease on it to install it.
Fitting the injectors in the rail.
Pushing the rail in place.
And now the exhaust for the turbo.
Adding the turbo's
The upgraded oilfeed lines from GTM
Next the oil return piping.
keep You Updated..
03-29-2011, 03:23 PM
#47
Registered User
Join Date: Mar 2007
Location: Fayetteville, Georgia
Posts: 168
Likes: 0
Received 0 Likes
on
0 Posts
fuel rail
What is that set up at the back of the fuel rail...the rear fitting look to bolt up to 2 cylinders with a hose connecting them...
Where is the fuel inlet port to the rail(s)?
Where is the fuel inlet port to the rail(s)?
Last edited by Zume; 03-29-2011 at 03:25 PM. Reason: clarity
03-30-2011, 11:45 AM
#48
Registered User
Thread Starter
Join Date: Dec 2007
Location: Netherlands
Posts: 209
Likes: 0
Received 0 Likes
on
0 Posts
06-21-2011, 05:52 AM
#55
Registered User
Thread Starter
Join Date: Dec 2007
Location: Netherlands
Posts: 209
Likes: 0
Received 0 Likes
on
0 Posts
No updates yet.. I had some health issues, nothing serious but a delay for a month. 
starting on the wiring harness from the front of the engine to the back this week..
starting on the wiring harness from the front of the engine to the back this week..
06-21-2011, 08:43 AM
#56
Registered User
iTrader: (1)
Join Date: May 2010
Location: Okotoks
Posts: 478
Likes: 0
Received 0 Likes
on
0 Posts
Hope it's clear sailing ahead for both your health and your build. Awesome job! Very, very impressive. Also great for the community to really look close at your photos and help out. Good eye cass!
06-27-2011, 01:12 PM
#58
Registered User
Thread Starter
Join Date: Dec 2007
Location: Netherlands
Posts: 209
Likes: 0
Received 0 Likes
on
0 Posts
So the wires are going te the Back to clean the engine room.
I received the haltech WB sensors. But where to put them in te exhaust?
Between the cats and turbo exit. This because the manual says 12 inch after turbo exit.
I received the haltech WB sensors. But where to put them in te exhaust?
Between the cats and turbo exit. This because the manual says 12 inch after turbo exit.
06-27-2011, 03:22 PM
#59
Shift_Boost
iTrader: (28)
Join Date: Dec 2005
Location: On a forum dedicated to Boost
Posts: 10,733
Likes: 0
Received 23 Likes
on
18 Posts
Love the color accents and the table. lol
only thing I'd do different would be a wastegate relocation kit. Gonna be a pain to get to them if you ever need to.
only thing I'd do different would be a wastegate relocation kit. Gonna be a pain to get to them if you ever need to.
Last edited by Old School; 06-27-2011 at 03:24 PM.
