My FI story
#81
Registered User
Thread Starter
Join Date: Dec 2007
Location: Netherlands
Posts: 209
Likes: 0
Received 0 Likes
on
0 Posts
The BOV is going just after te IC and before the MAF..
#82
Registered User
iTrader: (6)
Sorry, don't have any pictures, and I'm also on a different platform than you.
Placement shouldn't be a problem as long as you're willing to spend some time with cardboard to mock up the mounting and aluminum sheets for the mounting tabs.
The reason I suggested pre-intercooler was to prevent dumping cooled air. It may not make that big of a difference, if at all, but it's just something I prefer. Hell, my stock recirc valves are pre-cooler.
Looking forward to seeing more pics.
Placement shouldn't be a problem as long as you're willing to spend some time with cardboard to mock up the mounting and aluminum sheets for the mounting tabs.
The reason I suggested pre-intercooler was to prevent dumping cooled air. It may not make that big of a difference, if at all, but it's just something I prefer. Hell, my stock recirc valves are pre-cooler.
Looking forward to seeing more pics.
#88
Registered User
Thread Starter
Join Date: Dec 2007
Location: Netherlands
Posts: 209
Likes: 0
Received 0 Likes
on
0 Posts
#89
Registered User
Thread Starter
Join Date: Dec 2007
Location: Netherlands
Posts: 209
Likes: 0
Received 0 Likes
on
0 Posts
Its alive !!!!!
http://www.youtube.com/watch?v=xYFykIO8-ic
http://www.youtube.com/watch?v=0OhaBbRj9k4
Next week it is going to the tuner :mrgreen:
http://www.youtube.com/watch?v=xYFykIO8-ic
http://www.youtube.com/watch?v=0OhaBbRj9k4
Next week it is going to the tuner :mrgreen:
#93
Registered User
Thread Starter
Join Date: Dec 2007
Location: Netherlands
Posts: 209
Likes: 0
Received 0 Likes
on
0 Posts
We had to solve some oil leakes. After that we saw that 1 bank is running 20% richer than bank 2. This week I am trying to solve this.
Done so far
change fuel regulators.
Change fuel pomps.
No positive result.
What can it be. Any suggestions?
Done so far
change fuel regulators.
Change fuel pomps.
No positive result.
What can it be. Any suggestions?
#94
New Member
iTrader: (18)
Is the AFR imbalance under load or under vacuum or both? Under vacuum is normal because of plenum design (well, with the stock plenum). With the kinetix, I'm not sure. With an exhaust leak upstream of the O2 sensor, you might also get imbalance under vacuum. Under load it should equalize...
If it doesn't, test injectors per the FSM.
If it doesn't, test injectors per the FSM.
Last edited by rcdash; 11-29-2011 at 05:45 AM.
#96
New Member
iTrader: (8)
Join Date: Jan 2007
Location: terre haute, IN; STL, MO
Posts: 6,457
Likes: 0
Received 7 Likes
on
6 Posts
ya, i would say o2 problem causing incorrect readings.
possible manifold air leak on the lean bank side (unlikely though)
The chances of a whole bank of injectors being bad is rare and easy to test by swapping injectors between banks.
I know my cams are slightly off which causes a little bit of variance between my banks but only at certain vac cells. I was confused why i was having variances and then logged cam values and i assume that was the small issue. I'm not sure cams could create a 20% difference though. I would check to make sure both cams are at least working. If one has a wiring issue or a solenoid issue and is at 0* while the other is at 25* advance it could cause some problems.
possible manifold air leak on the lean bank side (unlikely though)
The chances of a whole bank of injectors being bad is rare and easy to test by swapping injectors between banks.
I know my cams are slightly off which causes a little bit of variance between my banks but only at certain vac cells. I was confused why i was having variances and then logged cam values and i assume that was the small issue. I'm not sure cams could create a 20% difference though. I would check to make sure both cams are at least working. If one has a wiring issue or a solenoid issue and is at 0* while the other is at 25* advance it could cause some problems.
#97
Registered User
Thread Starter
Join Date: Dec 2007
Location: Netherlands
Posts: 209
Likes: 0
Received 0 Likes
on
0 Posts
Widebands are calibraded.
all under vacum.
only drivers site all sparks are wet so i know it is on all 3 cilinders.
1000 rpm 20% richer
3000 rpm it is getting leaner then the passeger site.
Pfff.. i hope to solve this.. but no luck so far.
all under vacum.
only drivers site all sparks are wet so i know it is on all 3 cilinders.
1000 rpm 20% richer
3000 rpm it is getting leaner then the passeger site.
Pfff.. i hope to solve this.. but no luck so far.
#98
Registered User
Thread Starter
Join Date: Dec 2007
Location: Netherlands
Posts: 209
Likes: 0
Received 0 Likes
on
0 Posts
the strage thing is also tha at 1 point it was running fine for 1 minute and then it was off again... like the first video above....
Last edited by bjmax; 11-29-2011 at 10:21 PM.
#99
New Member
iTrader: (18)
If it's only under vacuum, why does it matter? 10.4 vs 10.8? Ignore! You can try checking your exhaust manifold and downpipe connection... A small leak under hard vacuum will suck in enough outside air to cause a slight imbalance, but it's completely irrelevant.
Last edited by rcdash; 11-30-2011 at 10:49 AM.