FS: 1000+ WHP Greddy Twin Turbo HR Kit w/Extras!
#1
Registered User
Thread Starter
iTrader: (5)
Join Date: Sep 2008
Location: Tampa
Posts: 511
Likes: 0
Received 0 Likes
on
0 Posts
1000+ WHP Greddy Twin Turbo HR Kit w/Extras!
Ladies and gents, I have decided to move to the S&R single turbo kit for the HR/VHR because it benifits my cars purpose better.
So, I am selling my Greddy Twin Turbo "HR" kit with the 20G's upgraded with 60-1 compressor wheels and upgraded thrust bearings. These were last serviced about 6 months ago!
The kit also includes the extended capacity oil pan, 2 Turbosmart Raceport BOV's, the Tial wastegates with 7lb springs, K&N air filters and the intercooler.
The turbo's have the DEI Titanium blankets on them (one has been worn by the steering column), the headers and downpipes are also completely wrapped with DEI titanium heat wrap.
For those who don't know, we have made over 1,000whp with this kit (it was probably closer to 1,200whp but the dyno hard drive skipped) at 29PSI.
We made 650whp at 14psi on pump, 805 at 15psi on Q16, and 940whp at 22psi on Q16. Obviously this will vary build to build but the larger flowing compressor wheels greatly contribute to this.
The piping and intercooler are powder coated green but can easily be stripped and re-powdercoated fairly cheap. The drivers side pipe to the throttlebody has had the powdercoat scuffed a little by a braided line but again, a strip and re-powder coat is cheap.
For the kit, including all mentioned above, the price is $5,500 w/shipping, no paypal fee's.
There is a good $14,000.00 worth in this "PROVEN" kit so the price is extremely good.
The kit comes off the car thursday so it could ship Friday or Monday!
Any questions, let me know. Below are some images.
So, I am selling my Greddy Twin Turbo "HR" kit with the 20G's upgraded with 60-1 compressor wheels and upgraded thrust bearings. These were last serviced about 6 months ago!
The kit also includes the extended capacity oil pan, 2 Turbosmart Raceport BOV's, the Tial wastegates with 7lb springs, K&N air filters and the intercooler.
The turbo's have the DEI Titanium blankets on them (one has been worn by the steering column), the headers and downpipes are also completely wrapped with DEI titanium heat wrap.
For those who don't know, we have made over 1,000whp with this kit (it was probably closer to 1,200whp but the dyno hard drive skipped) at 29PSI.
We made 650whp at 14psi on pump, 805 at 15psi on Q16, and 940whp at 22psi on Q16. Obviously this will vary build to build but the larger flowing compressor wheels greatly contribute to this.
The piping and intercooler are powder coated green but can easily be stripped and re-powdercoated fairly cheap. The drivers side pipe to the throttlebody has had the powdercoat scuffed a little by a braided line but again, a strip and re-powder coat is cheap.
For the kit, including all mentioned above, the price is $5,500 w/shipping, no paypal fee's.
There is a good $14,000.00 worth in this "PROVEN" kit so the price is extremely good.
The kit comes off the car thursday so it could ship Friday or Monday!
Any questions, let me know. Below are some images.
Last edited by GAMERMODZoCOM; 07-13-2012 at 04:31 PM.
#7
Registered User
Thread Starter
iTrader: (5)
Join Date: Sep 2008
Location: Tampa
Posts: 511
Likes: 0
Received 0 Likes
on
0 Posts
However, as Frosty said, as long as you have an 07 or 08 350Z. This kit will not fit a DE.
Also, if you do have an HR, you can run more than 8 and still have a huge safety margin.
Trending Topics
#15
Registered User
yup you did I want to get a squared 10 front and rear set up with some 18inch wheels. I will probably stick with the GTC 01 models though. I just drove a friends Z with asquared setup and it feels way different (better)