PPE Longtube Headers
08-19-2012, 03:54 PM
#442
Registered User
Join Date: Jan 2010
Location: SC
Posts: 44
Likes: 0
Received 0 Likes
on
0 Posts
You're lookingat list price now.
http://www.ppeengineering-onlinestor...&categoryId=45
Stepped runners flow better at high rpm, but you will lose more down low.
It's reccomended with your hr to get stepped.
http://www.ppeengineering-onlinestor...&categoryId=45
Stepped runners flow better at high rpm, but you will lose more down low.
It's reccomended with your hr to get stepped.
08-20-2012, 11:19 AM
#446
Registered User
iTrader: (3)
Join Date: May 2009
Location: earth
Posts: 1,365
Likes: 0
Received 0 Likes
on
0 Posts
I would like to know as well, and PPE is building mine slightly different so I want to make sure the correct set gets mailed to me and not someone else. Thanks
08-24-2012, 04:58 AM
#449
Be patient it took while for me to get my 1st set and I was the only one.
These headers are made to order they are not sitting on a shelf waiting to be bought/shipped somewhere one day.
I know when my set was made they only had one guy making them could be different now though.
So out of the group who is installing these themselves?
I'm going to make a thread with my results good/bad so everyone can post in once theirs are installed. This thread is too long to look for the dynos.
Tougelabs what were your before and after numbers.
These headers are made to order they are not sitting on a shelf waiting to be bought/shipped somewhere one day.
I know when my set was made they only had one guy making them could be different now though.
So out of the group who is installing these themselves?
I'm going to make a thread with my results good/bad so everyone can post in once theirs are installed. This thread is too long to look for the dynos.
Tougelabs what were your before and after numbers.
08-24-2012, 06:50 AM
#450
Registered User
iTrader: (6)
Join Date: May 2009
Location: Lubbock, Tx
Posts: 267
Likes: 0
Received 0 Likes
on
0 Posts
Be patient it took while for me to get my 1st set and I was the only one.
These headers are made to order they are not sitting on a shelf waiting to be bought/shipped somewhere one day.
I know when my set was made they only had one guy making them could be different now though.
So out of the group who is installing these themselves?
I'm going to make a thread with my results good/bad so everyone can post in once theirs are installed. This thread is too long to look for the dynos.
Tougelabs what were your before and after numbers.
These headers are made to order they are not sitting on a shelf waiting to be bought/shipped somewhere one day.
I know when my set was made they only had one guy making them could be different now though.
So out of the group who is installing these themselves?
I'm going to make a thread with my results good/bad so everyone can post in once theirs are installed. This thread is too long to look for the dynos.
Tougelabs what were your before and after numbers.
08-24-2012, 11:31 AM
#453
I was planning on doing the install myself, but considering the fact that my block burns 1 QT of oil / 1K miles, I really need to pull the block and do a build. I'm at the point where I'm not sure if I want to waste any more time / money on this platform. I'm sure if I had a HR without oil consumption I wouldn't feel that way 
Long story short, there might be a set of PPE Headers available in a few weeks.
Long story short, there might be a set of PPE Headers available in a few weeks.
08-29-2012, 07:30 AM
#460
Vendor - Former Vendor
Thread Starter
Join Date: Oct 2011
Location: Danbury
Posts: 145
Likes: 0
Received 0 Likes
on
0 Posts
I emailed Paul about tracking info and I'm hoping to hear back from him today. I'm sorry for not getting back to you guys. Been in horrific pain since the surgery, as for the hardware kits I'm closing it out as of now and have since put the order in for everything should have everything in by the end of this week and will hopefully have it out to you guy's that ordered/payed the same day. I know six headers went out today and another set will go out tomorrow from jet-coat. Sorry for not having any more information, as soon as I have more I will let you guys know.