NA Build Inside....Soup to Nuts :)
#123
OGPremierMafia
iTrader: (16)
Join Date: Feb 2005
Location: Cincinnati OH
Posts: 5,106
Likes: 0
Received 0 Likes
on
0 Posts
Adam, where did you source your 3" MAF housing, and down it have stock mounting. I was thinking about this for my TN kit. This is a great DSM trick for an extra few hp up top.
#124
Former Sponsor
Thread Starter
iTrader: (564)
Join Date: Feb 2003
Location: Long Island, New York
Posts: 19,266
Likes: 0
Received 5 Likes
on
5 Posts
Originally Posted by MI 35th
Adam, where did you source your 3" MAF housing, and down it have stock mounting. I was thinking about this for my TN kit. This is a great DSM trick for an extra few hp up top.
direct replacement...but def needs tuning to make it work
#128
Z + Rear Seat
iTrader: (3)
Join Date: Jun 2005
Location: St.Pete,FL
Posts: 1,642
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Z1 Performance
The MAF housing was a suggestion from one of the guys in Japan...he said it would prove beneficial, and he was right We got to the low 290's on the stock housing and then said, what the hell, let's toss it in and see what happens.....nice gains in mid range torque, though I can't tell you if we could have achieved those goals with the stock housing or not.
Originally Posted by Z1 Performance
Also, in talking with the engine guru today, he touched on something that he things will prove very beneficial as far as my tune is concerned...I am looking forward to trying it in the next two weeks, once HIN is done
#130
Z + Rear Seat
iTrader: (3)
Join Date: Jun 2005
Location: St.Pete,FL
Posts: 1,642
Likes: 0
Received 0 Likes
on
0 Posts
I wonder if there's a preferred sequence to these mods? Maybe the 3" MAF doesn't help unless you've all ready got headers, HFC's and cams...
The 3" MAF does seem like a trick piece, though...
The 3" MAF does seem like a trick piece, though...
#131
Registered User
....and means nothing without tuning. A larger MAF housing REQUIRES tuning (WOT and part-throttle as well) as it will make the AFR very lean. Not a bolt-in and go mod. Takes time to dial it in. But once dialed in, it's a legit mod. Good for ~8-10WHP on VQ35 maximas with bolt-ons.
Last edited by nismology1; 07-10-2007 at 11:18 AM.
#135
New Member
iTrader: (78)
Originally Posted by Nismo 350z
http://www.topsecretjpn.com/products/vq35itbx.jpg
Top Secret ITB kit. 6K$ but probably one hell of a mod especially on a NA car.
Top Secret ITB kit. 6K$ but probably one hell of a mod especially on a NA car.
#136
Former Sponsor
Thread Starter
iTrader: (564)
Join Date: Feb 2003
Location: Long Island, New York
Posts: 19,266
Likes: 0
Received 5 Likes
on
5 Posts
Originally Posted by RedBullRR
Sounds real expensive for such that kind of gain.
#137
Former Sponsor
Thread Starter
iTrader: (564)
Join Date: Feb 2003
Location: Long Island, New York
Posts: 19,266
Likes: 0
Received 5 Likes
on
5 Posts
Originally Posted by __jb
Hopefully you will think about turning some of these pieces into commercial products and selling them to us...
Adam... Your message got cut off right where you were going to tell us what this tip was... please resend the full message... Thanks...
Adam... Your message got cut off right where you were going to tell us what this tip was... please resend the full message... Thanks...
nothing earth shattering, just something we should have been doing that we didn't...I'll be back on the dyno week after next !
#138
Former Sponsor
Thread Starter
iTrader: (564)
Join Date: Feb 2003
Location: Long Island, New York
Posts: 19,266
Likes: 0
Received 5 Likes
on
5 Posts
Originally Posted by NA&CH
Didn't Jeremy use the 3" on his n20 car? Stock everything? He used it from a ford, I think? Correct me if I am wrong. Is it similar Adam?
Chris
Chris
#139
Former Sponsor
Thread Starter
iTrader: (564)
Join Date: Feb 2003
Location: Long Island, New York
Posts: 19,266
Likes: 0
Received 5 Likes
on
5 Posts
Originally Posted by Nismo 350z
http://www.topsecretjpn.com/products/vq35itbx.jpg
Top Secret ITB kit. 6K$ but probably one hell of a mod especially on a NA car.
Top Secret ITB kit. 6K$ but probably one hell of a mod especially on a NA car.
But, there is absolutely zero info on it, and I know of 0 cars using aside from their own. At $6k, I want a bit more of a known commodity!
#140
New Member
Originally Posted by Z1 Performance
if they gave it to me at 50% of retail, I'd consider trying it
But, there is absolutely zero info on it, and I know of 0 cars using aside from their own. At $6k, I want a bit more of a known commodity!
But, there is absolutely zero info on it, and I know of 0 cars using aside from their own. At $6k, I want a bit more of a known commodity!