Steve, I have already put the word out to a few people, and there seems to be a lot of interest. If I reacall I think you had a great idea for recruting at a test n tune.

 

You know as always I am in....
$50.00 we will get ALOT more interest...

 

Thats what I am hoping. I want to see who is interested before I try and do this again.

 

OK First event of the year!!

Gilson Motorsports is doing a Street/Track Alignment Tech Session this Saturday at their shop. Now this is sort of only for Porsche Club Members, but since Steve and I both did a couple HPDE's with them last year, I called them up and they were cool with a few 350Z's guys showing up.

Here's the info:

Gilson MotorSports would like to invite you to a Tech Session where ALIGNMENTS will be explained in detail. It is essential to how your car drives. We will show you how a custom alignment is done before you go to the track. If you drive your car with spirit, you will not want to miss this Tech Session. We will be using the Smart Racing Products Alignment Equipment for the demonstrations.

Included in the program will be:
4 Wheel Custom Alignments
Tire Pressures
Ride Height
Camber
Caster
Toe & More.

A good Alignment is crucial to a fun and successful driving experience.
SEM/PCA Sponsored Event.

His shop is located in Royal Oak so if any of you guys wanna show up I think it'd be cool to hang out for a bit. As long as we be polite and don't eat all their food haha.

Anybody down? Temps in the high 40's and sunny = the Fairlady will come out

 

yes! whats the cost?

 

Whats the cost, what time I might come out and learn a bit.

Suspension Geometry is for sure one of my weak points

 

i just want a street setup that doesn't shred tires

 

uhhh from my understanding it's free. Basically taken out of the SEMPCA membership dues. Which is why I made the comment on not eating their free food lol

and Howard's a pretty cool guy, as long as we're cool and respect him and his place for letting us join

 

For $50 I would be down for sure. Haha, not that my one car would make a difference I'm sure. Just figured I'd voice that, in case you want to get something going.

 

this is sounds like a full corner balancing and aligment , this is ain't gonna be cheap guys at least 300 bucks . this is only neccasary if you have coilovers and drop with a camber kit to correct the camber issues .

 

i have coilovers and alignment bolts in the rear, but my car is not very low any more, under a 1 inch drop.

 

guys this is just a class to show how to do the alignment. They're not actually doing alignments to customer cars, just showing how to do one and explaining the theory behind it all.

 

If thats the case then I will be there.
Barring any unforseen things...

I know $hit about this and want to learn..

 

Thanks AznSky. Actually, I work in AA around the airport area. My car was sitting in the garage all winter, just took it out twice last week or so.

I am also interested in going to the track, its a different story if I will race. I am still a novice when it comes to track. This is my first stick car.

 

Rob - I'm going to try to get over to Gilson's on Saturday for the alignment class/workshop.

I'll probably use that time to sign up for the first PCA/HPDE on 5/14 at Waterford too..

 

Alignment Tech Session:

Ok whoever is planning on going to the tech session tomorrow, please let me know. I'll PM you the address and phone number.

Steve, can you PM me your cell again? I washed my old phone so I lost everybody's number haha.

AJ if you want, I can just swing by your place and pick you up since it's along the way.

on a separate note, drove the Z into work today and it felt grreeaaat!!

 

Rob,
yeah man that would be great actually.
Give me a call tonight if you can, I think I PM'd you my #
That way I am ready to go for tomorrow

 

i was wondering do any of you guys kno a good performance shop that has experience on Z's? i need my nx kit installed asap

 

As AJ would put it, "we're the best shop to work on Z's here around SE Michigan" haha

And it was good to see everybody this weekend too. Hopefully everybody will come out to the mod party april 4th so we can all hangout

 

i tried installing my test pipes yesterday. after realizing the floor jack was too tall and having to buy ramps, i made the mistake in thinking it would only take a couple hours tops. i think i went through half a can of liquid wrench, and the bolts i could get to still wouldn't budge! i got one bolt off. that was it.

for the upper part of the cats, where they connect to the headers, 2 of the 3 bolts are next to impossible to get at. is there a trick?!

needless to say, i put it all back together and gave up (which i hate doing) for the night. after a couple hours and many bumps, scrapes and nicks later. Z=1. scott=0.