Sorry for the triple post but could you guys who are dynoing PM me wth a list of your performance mods. I'm going to start getting the dyno sheet together so I can record all the numbers with the persons name and mods... Thanks.

 

Um, regardless of where we go I cannot see any of the operators allowing for a Y-Pipe change???

I'll send ya a PM in a sec here.

I'd like to have the printout as well ... 2 pulls is enough for me

Jim

 

I dont care either but whoever we're gonna go with we need to make up our minds!!

 

AGREED!!!! Lets make the cutoff to decide like Tues.

 

If a ypipe change isn't possible, then i'll just get a baseline with what mods i currently have and then dyno with the ypipe at a later date, but i definitely want a/f graph. Would aebs give us two pulls with a/f graph?

 

Rob,
All my current mods are included at bottom of my signature. Will that do?

 

Yeah thats fine I guess...as far as dynos its not that AEBS won't do the A/F its that they dont have the ability to print it. They use a real time scanner similar to a wideband O2 during the run to read real time A/F...

 

Rob, sent ya a PM.

I don't mind only getting two pulls if I get an a/f printout. With the mods I have, many others report running lean. I'd like to know if I need to do additional tuning to the a/f curve.

 

Well sounds like its going to be Autotech. Oliver can you talk to your guy and see what we can setup?

 

Autotech it is then! Mods in my sig.

 

Aight guys, I'll call the guy first thing in the morning. Don't cancel the other shop until I verify tomorrow that this thing is for sure. I'm not worried, just bein safe. Anyways, I just found out that I'll be joining you guys that morning for the dyno. Woohoo! I went with a smaller fuel jet so I'm hoping my A/F is more around 11.5-12 and maybe a little more horsepower. I'll be there at 8:30am so I can go first. I got my grandma's bday lunch to go to, hope its cool with everyone.

Anyways, since there was this last minute change, everyone who's goin for sure please put their name on the list. So we know you read this. I'll pm everyone on the list my cell, just in case they got any questions, or if they just want a good time, Haha

Where: Autotech Motorsports

http://www.smartpages.com/home/autot...EBSBQFI4GCQ4CQ

When: Saturday, Aug. 28, 8:30am

$70, 2 pulls, w/ printouts

1. Cyberz350
2. MIAPLAYA
3. BrImSt0ne
4. Steel Heals
5. Z BOY
6. JimRHIT

 

Works for me...updated list
1. Cyberz350
2. MIAPLAYA
3. BrImSt0ne
4. Steel Heals
5. Z BOY
6. Nismo2k2specv (b15 boards)
7. CrazeD_SpecV (LS1 style)

 

Works for me...updated list
1. Cyberz350
2. MIAPLAYA
3. BrImSt0ne
4. Steel Heals
5. Z BOY
6. Nismo2k2specv (b15 boards)
7. CrazeD_SpecV (LS1 style)
8. JimRHIT

 

O.K. fellas, I talked to the guy and this thing is on and poppin!!!. MIAPLAYA, I guess you can tell your friend that we won't be able to make it, don't wanna string him along. Let me know if you guys have any questions.

1. Cyberz350
2. MIAPLAYA
3. BrImSt0ne
4. Steel Heals
5. Z BOY
6. Nismo2k2specv (b15 boards)
7. CrazeD_SpecV (LS1 style)
8. JimRHIT

 

whoever pmed me try again

love me baby

 

I'll call AEBS today and let them know. I'll also call Nismo2k2 and CrazeD to let them know as well. Oliver what did the guy say about changing jwkirklands boost pulley?

 

Boost pulley isn't a problem. I asked the guy just now and I told him it was gonna be pretty quick and he said it should be cool. As long as it doesn't take a half an hour or something haha.

 

OK officially canceled with AEBS. Oliver, What time should we be there on Saturday? It is still $70 right?

 

And Oliver dont forget to give us an address or directions. Not gonna make it to the gtg 2nite so i'll see you guys on saturday.

 

Cool.. this new place is closer to my house