Originally Posted by Kristi

^ I had a Jetta before this and that damn thing was always in the shop getting repairs

Originally Posted by Kristi

We hopefully will have Tommy's car somewhat done so we will be there

Originally Posted by Kristi

yeah his springs came in yesterday and his wheels come in tomorrow
hopefully sometime here soon we can get it in to the body shop and cut his rear fenders out... I have a feeling they are going to rub bad :/

Originally Posted by JasonZ-YA

dammnn, does anyone know where to buy aluminum Tee angle in town??

-J

Originally Posted by AcidJake75

Cut! Body Shop!? wth? why not roll them hoes? bad offset? if they are cut - wont they have to repaint? ohh man..Im gonna make fun of him on IM right now..

Originally Posted by FishBrownie

What size are you looking for? I can check with the manufacturing building I work in and see what they have. They build airplane interiors, so they usually have several sizes of AND extrusion laying around. Not sure about any tee extrusion, but I can ask.

Originally Posted by AcidJake75

Cut! Body Shop!? wth? why not roll them hoes? bad offset? if they are cut - wont they have to repaint? ohh man..Im gonna make fun of him on IM right now..

Originally Posted by JasonZ-YA

Awesome, yeah im looking for a Tee extrusion - say 1" x 1" Tee to 3" x 3" tee with anywhere from .050 to .125 thick.

The main thing is it cant be too thick, i can cut down the legs as i need..

I need the piece for the "how to" jake and I recently did:
https://my350z.com/forum/engine-driv...voir-swap.html

let me know what you find? I would like a foot of it, but pieces 3 inches long would be all i need to make the mount.

Thanks so much...

-J

Originally Posted by Kristi

you guys are lucky with your manual's - the auto takes so many Quarts of fluid that it is cheaper to take it in to the dealer than it is to do on your own... not to mention the labor on manuals is easier, the auto they place the drains/fill in hard to reach places

I almost got t-boned this morning on the way into work by a Honda odyssey - damn old oriental ladies can’t drive... she would have taken out my entire driver side if I didn’t swerve... I got out of my car and started bitching her out, she apologized over and over again and started crying.. I think she thought I was going to go up to her car and beat her *** or something.... but I was so pissed...



ANYWAYS Good Morning DFW

Originally Posted by fithamoto

Hey that was my Mom !
She told me that some crazy Blonde girl in a Z bitched her out.

Well it could have been.

Originally Posted by FishBrownie

J,
no luck here. They only have L-angle. They checked around with a few other places that may have it, and nobody does. They could order some, but at $100/ft for a min of 12 feet to get it made, I don't believe you'd be interested in that. I'd suggest just riveting 2 L-angle pieces together. That should hold just as well as a tee extr for what you are using it for. It's not like Jake is going to be pulling 9 g's while drifting.

Originally Posted by JasonZ-YA

lol ya, jake and I only hit about 7 or 8 g's...........

Ya, I mentioned using two L angles in the thread.....but i kinda wanted the oh so clean look.....oh well..

I'm now looking up plastic extrusions online, seeing if i can get a plastic T shipped to me......that would work fine..

I called a few salvage yards, and they all say that they think they have some laying around, but you have to go in person and its hit or miss on what they have.....so i dont even wanna bother driving out to them unless they have what i need.

thanks so much for looking into it...

-J

Originally Posted by Kristi

wow it is slient in here now

Originally Posted by quakerroatmeal

Cutting it is better then having it rolled. They won't have to repaint it.

Kristi what wheels is tommy putting on that car?