[DFW]: DFW's Lounge
Joined: May 2008
Posts: 48,548
Likes: 3,339
From: Jakku
HAHAHAHA look at this picture of his, and the comment!!!
https://my350z.com/forum/members/nit...-discount.html
https://my350z.com/forum/members/nit...-discount.html
Kristi: definately take your car back to the installer and get them to fix it. The car was perfect when it went in and should be the same when it leaves.
I actually am an installer for Custom sounds here in Austin and i would never let a car leave with a problem, and if something does occur, i will take care of the problem if its either my install or equipment....weird though that it will not rev, does everything else work? who installed the alarm? does everything else work (lock, unlock, ect.) Is it a remote start alarm?
Where are the paintball stores???! i know a lot of fields have equipment too, but im wondering if there are any paintball stores where i can check out the gear and learn a bit more..
I haz the bug nowz...
-J
I haz the bug nowz...
-J
this might be a coincidence but yesterday we had an alarm installed on kristi's car. Everything was fine until we were about to leave. The Service Engine Soon, TCS OFF, and SLIP lights are all on and you can floor the gas pedal and the car will barely go.
When you start the car the rpms drops and the car dies or rpm drops and it has a rough recovery to idle or you give it a little gas when starting and it will idle
I have pulled the battery for 6 hours and tried again and the lights are still there. I even tried the manual ECU reset by turning key on and hitting gas pedal but nothing.
ANYONE?? I have not pulled codes yet.
When you start the car the rpms drops and the car dies or rpm drops and it has a rough recovery to idle or you give it a little gas when starting and it will idle
I have pulled the battery for 6 hours and tried again and the lights are still there. I even tried the manual ECU reset by turning key on and hitting gas pedal but nothing.
ANYONE?? I have not pulled codes yet.
Gotta pull them codes Tommy. 6 hrs is not long enough - Ive left mine unplugged overnight and it still doesnt reset. 24 hr min if you didnt do the pedal reset right. It will get fixed and I bet it was just something simple. Shouldnt be a big deal..
HAHAHAHA look at this picture of his, and the comment!!!
https://my350z.com/forum/members/nit...-discount.html
https://my350z.com/forum/members/nit...-discount.html
Joined: Mar 2007
Posts: 5,311
Likes: 0
From: Dallas/NewYork/Michigan/Korea
this might be a coincidence but yesterday we had an alarm installed on kristi's car. Everything was fine until we were about to leave. The Service Engine Soon, TCS OFF, and SLIP lights are all on and you can floor the gas pedal and the car will barely go.
When you start the car the rpms drops and the car dies or rpm drops and it has a rough recovery to idle or you give it a little gas when starting and it will idle
I have pulled the battery for 6 hours and tried again and the lights are still there. I even tried the manual ECU reset by turning key on and hitting gas pedal but nothing.
ANYONE?? I have not pulled codes yet.
When you start the car the rpms drops and the car dies or rpm drops and it has a rough recovery to idle or you give it a little gas when starting and it will idle
I have pulled the battery for 6 hours and tried again and the lights are still there. I even tried the manual ECU reset by turning key on and hitting gas pedal but nothing.
ANYONE?? I have not pulled codes yet.
It could be anything...Did you guys remove the TB or MAF sensor during install? without code it is hard to tell what is going on. Best bet is go back to all the wire and see if anything pinch or unplug.
Joined: Mar 2007
Posts: 5,311
Likes: 0
From: Dallas/NewYork/Michigan/Korea
Prob thursday, i heard you coming over on friday. I will be there on saturday to doing what i can do over there. I have to get myself ready to delete my tune. It will be fun 
Oh i gave him your gasket that goes between TB and plenum.
Edit: also wheel buyer is coming from houston this saturday...god...everything is gone really fast....

Oh i gave him your gasket that goes between TB and plenum.
Edit: also wheel buyer is coming from houston this saturday...god...everything is gone really fast....
Last edited by Chef-J; Sep 15, 2009 at 07:03 AM.




