Osiris from Uprev
#721
New Member
iTrader: (18)
Has anyone had their radiator fans come on during the reflash process? Good thing I had a battery charger/starter hooked up cause they started sucking down the juice... The flash went through just fine, but I'd be scared to run this without being hooked up to AC power...
#722
Registered User
iTrader: (12)
Originally Posted by rcdash
Has anyone had their radiator fans come on during the reflash process? Good thing I had a battery charger/starter hooked up cause they started sucking down the juice... The flash went through just fine, but I'd be scared to run this without being hooked up to AC power...
#724
Registered User
iTrader: (1)
Join Date: Oct 2004
Location: Germany
Posts: 182
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by rcdash
Has anyone had their radiator fans come on during the reflash process? Good thing I had a battery charger/starter hooked up cause they started sucking down the juice... The flash went through just fine, but I'd be scared to run this without being hooked up to AC power...
#725
Registered User
iTrader: (12)
Originally Posted by r3zon8
how does the car feel after the flash?
i wish there was a Miami guy that I could take a ride with and see if i feel the difference.
i wish there was a Miami guy that I could take a ride with and see if i feel the difference.
You or at least I can tell what I feel to be the Optimized Throttle Control.
My Maps look like this:
Idel: Stock
Map 1: Economy: Stock + Optimized Throttle Control Map, Air/Fuel Tuning
Map 2: Valet: 3200 rpm limit, 30 mph
Map 3: Sport: 93 octane tune, 7400 rpm, No Speed Limiter, Optimized Throttle Control Map, Air/Fuel Tuning.
Now UPREV Added these two:
Map 4: Economy mode (13.25 AFR targets, 4400RPM rev limit)
Map 5: Stock
Over all I am real excited to see how it all turns out after my First e-tune. I am going to be logging these Parameters. This something i found on this post:
A/F CORR-B1 (%)
A/F CORR-B2 (%)
AFR WB-B1 (AFR)
AFR WB-B2 (AFR)
A/F WB-B1 (V)
A/F WB-B2 (V)
ACCEL PED POS 1 (V-Accel)
B-FUEL SCHDL (ms)
CAL/LD VALUE (%)
COOLANT TEMP (F)
ENGINE RPM (rpm)
IGN TIMING (BTDC)
INJ PULSE-B1 (ms)
INJ PULSE-B2 (ms)
INTAKE AIR TMP (F)
MAF GM/S (gm/s)
MAS A/F -B1 (V)
THROTTLE POS 1 (V-Throttle)
VEHICLE SPEED (mph)
Now according the the FAQ at www.uprev.com all you need to log is:
What parameters should be logged for AFR eTuning?
AFR Bank 1 and Bank 2 (See Cipher user guide)
Accelerator position (either one)
Base fuel schedule
Calculated load
Coolant temp
Engine speed (RPM)
Ignition timing advance
Throttle position (either one)
I will see how it goes.
Chad
Last edited by cdoxp800; 02-12-2008 at 01:04 PM.
#726
New Member
iTrader: (18)
Originally Posted by Silo
That's intentionally triggered to stabilize voltage while flashing. No worries. I have flashed with voltage as low as 11,74V and I recall there is a security feature to not let you start the flash process below a certain battery voltage.
That's not a good idea, if it's intentional. My fans draw a LOT more current than the stock fans. I don't understand why the voltage would need to be brought down...
On another note, it seems that the max idle rpm is 850, even though I asked for 1000. I then asked for 800, and it was 800. Sorry if this has been answered before but this is one long thread!
#731
Registered User
i dont know if anyone has said this b4 but on their web site where it shows the dyno sheets. the second one down where it says "06 revup AT" there is no such thing as an automatic rev-up