so where can i get my hands on a Fujita besides Car Domain and Ptuning since they have been out of stock for a while now.. any other sources out there or where are you guys getting yours

 

Took me about an hour and a half to install mine today. But I have to admit I'm **** and repositioned all the hose clamps about twice each!!

This is my 1st Z (thus my 1st intake install on a Z), and it took me about thirty minutes to finally wrestle the stock driverside intake snorkle out of the engine bay!! Here's a hint for other 1st timers.... Pull it through the hole into the engine compartment. Eventually with enough leverage it will bend and pop through.

Sounds really nice, but now I need an exhaust because all I hear is intake!!!

 

Intake modifications on the HR should be stamped with uncle bens ricer seal of approval.

 

I'm getting mine on tuesday too.... Let me know if yall doing a dyno i wanna dyno mine too... and intake install is easy.. i took my whole intake out in less then 15min....

 

thanks for the info.

 

where are some places i can get my hands on this?

 

Cool

 

San Antonio guys. Let me know when you are going to dyno. I need to go again after some disappointing results in 95 degree/ high humidity conditions. Just want to see what other Zs with similiar mods are doing. I can get us a discount rate if at least 5 of us go.

 

I get may on tuesday I dont know time.I can go any day just let me know like a day before except this wednesday I am out of town,but like I said just let me know I got a flexible job .

 

Mine arrived! This will be my second intake install (my first was a Scion tC) I hope its not too hard!

 

We both switched to Z's from a tC. Traded my 07 tC in for my Z lol

 

Where are the dynos!?

 

Same place the added power is.

 

the Dyno place call me yesterday, and tell that they got problems with their dyno,speed sensor problems and they will call me when fix.

 

what i would have done is before and afters on the dyno...this way you still see what the gains were even with the bad weather.

 

Hmmm I thought I posted this last night:

Anyway, I installed mine last night. Took a bit of time because I dropped and had to fish out a 10mm bolt from under the engine block - NOT FUN.

Some Notes:

• The crankcase tubing *is* a *****. The type of angle you need to bend the tubing at pretty much cuts the total circumference of the tubing in half --- I have no idea if this is okay or not, but the angle is awful. This is probably the only negative side of the actual design of the intake.
• The stock air vents are a PAIN to remove. I damn near gave up and was about to remove my front bumper before I got the angle right and put a little muscle into it.
• It seems like I gained a LOT of torque and low-end with the intake. Take off from a stop is noticeably faster. I'll be interested to see what my new 0-60 timing is.
• Very minimal gains in the mid-range from 3.5-5.5k rpm
• A noticeable increase in throttle response in the higher RPM range.
• The sound is amazing. The stock exaust note is a little deeper and slightly throaty. The engine is louder and deeper all around, but not raspy. Its a very nice note.
• The NOS energy drink that CarDomain included in the box tasted absolutely awful.

I will post plenty of high-res images and close ups later today, as well as a movie with some decent sound.

 

You did... You posted it in another Fujita Intake thread:

https://my350z.com/forum/intake-exhaust/295043-fujita-07-dual-intake-install-finished-some-small-tips.html

Now get some sleep!!!

 

Well I just got it and the dyno that I was going to is broken,so I dont know how long I can wait .Those intake are sitting in my living room just waiting to be installed.Any one from San Antonio know any shop with a dyno that I can do my dyno runs.

 

oops. theres two threads...?

I got 3 hours last night

 

You should post this question as a new thread in this sub forum.... This thread is pretty much relegated to 07 owners (for the most part anyway), you will get more views outside this thread... Then come back with the results of the dyno pulls...