350zspl, do you have a source for amp schematics? I need one for an old school Rockford Fosgate Punch 800a2. One of the MOSFETs and probably the bias resistor is toasted. My friend gave me 4 old school amps to fix and they're all cheapies(Targa, Earthquake, ect..) except this one.

 

schematics i do not know were to get , possibly Rockford Fosagte Tech can provide

i know you can get a view of the internals on the amp guts section at Realm Of Excusrion website


if you post a thread on
Termpro Forum
Realm Of Excursion Forum
Ecoustics Forum
Rockford Fosgate Forum

someone may chime in and provide schematics

sorry

 

Here is an update on the box. Needs finishing coat of paint.





So far I am very happy with the look of the box and the only flaw I have seen on it will be covered by the bondo matched panels that will blend into the sides. I Have not seen it in the car yet. If I put it in and it sticks out like a soar thumb, I will be painting it black to match interior panels.

 

can't wait to hear your review when sub is bumpin

 

I'm sorry but I had to post up this really old picture that I just found, lol...

 

that walled off z is sick

would love to see finished product


i am sure 99.9% members see a ruined car
i see possibilities

 

OMG that **** is a monster!

 

It's pretty extreme

 

Ok, how much would it cost to get you do duplicate that and ship to 30345? Any pics in the car? Maybe I could just get some tips from you on f-glassing. I'll PM you about glassing if I get adventurous.

Haha, I remember that.

 

that wall looks like 2 x 12" but not 15"

anyone got pics of finished product

and needs x 2 baffle

 

Nope, the orginal poster, posted it up on Motoring and that was it , never heard or seen from the guy since, maybe it didn't work out.

 

dkmesa350z,

Just going with a rough estimate, the box and shipping will probably be around $1500.

If you are interested, there are a few things to note:

1. Will need a spec sheet of your sub faxed or emailed
2. Can only do a textured finish (the pic is a textured finish, not gloss paint like you would see on a car). The finish is not smooth like a body panel.
3. We are working to finish competition vehicles before Spring Break Nationals right now so it would be a couple of months from now (April or May) before we would be ready to ship.

If you are interested in trying it yourself, I will be more than happy to let you know everything we did and used.

Here is a pic of what it looks like in the car:



I have better pics that I can post if you would like.

 

Could you post a bigger picture of it in the trunk?

 

When all is said and done, you will only be able to see about 6" of the box from the top. The rest of the box will be covered by a vinyl covered bondo matched floor.

 

OK, I finally got the sub mounted and wired for sound.

First, the sub pounds!

Unfortunately, I am using the processing from the Alpine D310 head unit until I get the cable to connect my controller to my H701 processor.

The sub sounds great but is crossed over way too high (80 Hz w/ a 12 dB slope - only x-over point the head unit gives me). Once I get my processor hooked up, I will x-over the sub around 45 Hz and I am sure that it will sound great.

Once I get the front stage and panels finished I will post pics.

 

i like to crossover at 60

there is some mid bass you will cheat yourself out of at 45

46-60 will yeild decent mid bass your 15" can pound


but 45 is not bad

i am doing a 15" as well

new box should be at my door step this week

 

I am going to go up to 45 Hz on the sub and have my mids cover anything higher than that.

I have heard the Morels that I purchased in a frined's vehicle and they sound ridiculous, so they will handle it.

I will make a bass setting on the H701 and x-over around 50 Hz when I want to get down...

Did you order a new sub? What kind?

 

50 works perfect and you can reduce to 45 if you do not agree

the Morels are sick

i am going back and forth between a 15" RD Heavyweight DVC 1 ohm and a 15" atomic apocalypse apxx

i have already paid in full for box and sub

let you know which sub i choose leaning toward the atomic




APXX 15

Quick Specs
- Super Extreme SPL competition Woofer.
- 3 seconds short burps up to 30,000Watts.
- Custom impedance matching to your amplifiers.
- One of the highest efficiency Woofer in its class


Super eXTREME SPL competition woofer
* high sensitivity, extreme efficient motor to ensure high SPL possible
* Rigid Die cast aluminum basket
* Organic long fiber non-pressed cone body for accurate tight bass
* Highly damped Kevlar and carbon fiber reinforced cone body
* triple layers foam surround increase the power capacity of woofer
* Extended neck joints on cone, coil and spider strengthen the integrity of moving structure for high power capacity
* Compressed mounting ring gasket
* vented coil for extra heat dissipation
* 3 inch high temp aluminum voice coil
* extended, machined cut one piece back plate
* Powerful double stacked high energy magnet
* over 2-1/2 inch long excursion motor structure
* reinforced resin impregnated polycotton spider extend the life span of the speaker from material fatigue and collapse.
* integrated heavy duty lead wire on spider prevent short circuit and melt down
* dome shape dust cap design
* low carbon front and back plate
* Vented magnetic gap technology
* Laser etched, machined and chromed back plate