Any Project Mu B-Force owners?
#1
Registered User
Thread Starter
iTrader: (55)
Join Date: Nov 2004
Location: ORLANDO, FL
Posts: 5,276
Likes: 0
Received 0 Likes
on
0 Posts
Any Project Mu B-Force owners?
I'm starting to be convinced that these pads are crap. I installed them and bedded them and no go on silence. The squeak real loud on me. I understand they are a more aggrressive pad but the squeak is LOUD. I don't mind a small sqeak/noise.
I knew i should have went with Endless.
I knew i should have went with Endless.
Trending Topics
#9
Registered User
Thread Starter
iTrader: (55)
Join Date: Nov 2004
Location: ORLANDO, FL
Posts: 5,276
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Volk350Z
hmm that's weird.. cause i only hear mine with its cold.. where did you get the rotor/pad install?? also did you break in the rotor & pads??
#10
Master
iTrader: (65)
Join Date: Sep 2005
Location: SoCal
Posts: 2,527
Likes: 0
Received 0 Likes
on
0 Posts
well you are suppose to do it like this at the beginning..
1) drive like 50 mph and stop hard to 10mph but dont lock up the brakes
2) do it like 5 times
3) cool down and do it again
4) but dont lock up the brakes
5) if u lock it up...the rotor might heat up too fast and u'll warp the rotor
1) drive like 50 mph and stop hard to 10mph but dont lock up the brakes
2) do it like 5 times
3) cool down and do it again
4) but dont lock up the brakes
5) if u lock it up...the rotor might heat up too fast and u'll warp the rotor
#11
Sponsor
Performance Nissan
Performance Nissan
iTrader: (92)
Join Date: Dec 2004
Location: Pasadena/Bay Area
Posts: 6,151
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Volk350Z
well you are suppose to do it like this at the beginning..
1) drive like 50 mph and stop hard to 10mph but dont lock up the brakes
2) do it like 5 times
3) cool down and do it again
4) but dont lock up the brakes
5) if u lock it up...the rotor might heat up too fast and u'll warp the rotor
1) drive like 50 mph and stop hard to 10mph but dont lock up the brakes
2) do it like 5 times
3) cool down and do it again
4) but dont lock up the brakes
5) if u lock it up...the rotor might heat up too fast and u'll warp the rotor
#12
Registered User
Thread Starter
iTrader: (55)
Join Date: Nov 2004
Location: ORLANDO, FL
Posts: 5,276
Likes: 0
Received 0 Likes
on
0 Posts
That's what i did. I found that procudure searching the forums.
How would i know if my rotors are warped? What should i look out for? I did bedding from 80-90 mph yesturday and i see slight discoloration around the middle of the rotor.
How would i know if my rotors are warped? What should i look out for? I did bedding from 80-90 mph yesturday and i see slight discoloration around the middle of the rotor.
#14
Dr. Wired
iTrader: (2)
Sometimes brakes are noisy. Does that make them crap? Hardly.
I'm sure a little bit of the right grease in the right spots (not on the rotor :P ) and you will have no more noise.
If you see the "discoloration at the center of the rotor" that usually means the bedding in was successful (I think!) at least, it was like that when I bedded mine in.
For the record, my axxis ultimate pads squealed really bad when I first got them on. They only squealed when I was braking lightly. This happened for like 1500-2000 miles even though they were bedded in properly. Now they are dead silent. Go figure.
I'm sure a little bit of the right grease in the right spots (not on the rotor :P ) and you will have no more noise.
If you see the "discoloration at the center of the rotor" that usually means the bedding in was successful (I think!) at least, it was like that when I bedded mine in.
For the record, my axxis ultimate pads squealed really bad when I first got them on. They only squealed when I was braking lightly. This happened for like 1500-2000 miles even though they were bedded in properly. Now they are dead silent. Go figure.
Last edited by Wired 24/7; 08-16-2006 at 12:01 PM.
#16
Banned
iTrader: (42)
Join Date: Dec 2004
Location: Pasadena, CA
Posts: 459
Likes: 0
Received 0 Likes
on
0 Posts
Yeah, I didn't break mine any using any type of break-in procedure. I just installed them and drove on them normally. I experienced some loud squeaking when they were new, cold or hot. And now I RARELY hear them squeak, and it they do, its not very loud at all, I have to have the windows down and listen for it to hear it.
I've had mine for about 10k or so now, maybe a little more in the front.
I've had mine for about 10k or so now, maybe a little more in the front.
Thread
Thread Starter
Forum
Replies
Last Post
350Z_Al
Exterior & Interior
133
10-29-2020 07:44 PM
ars88
Zs & Gs For Sale
18
04-04-2016 07:52 AM