Special Edition StopTech's?
08-20-2007, 05:19 PM
#42
Former Sponsor
iTrader: (564)
Join Date: Feb 2003
Location: Long Island, New York
Posts: 19,266
Likes: 0
Received 5 Likes
on
5 Posts
Originally Posted by Justin@WestCovinaNissan
That would be so dope... if only they would come back out with Hypercolor shirts. 
AP used to offer this...and stopped within 6 months, as the paint frankly sucks for longevity
08-21-2007, 10:33 AM
#43
Registered User
iTrader: (10)
Join Date: Dec 2003
Location: one of the 5 boros, NY
Posts: 2,704
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by J Ritt
You dropped an LS6 in your Z?!?!? Nice!
I've always liked the looks of the 350Z better. That said, my Z06 is actually quite a bit lighter than my 350 was...and it handles a lot better too...can use wider tires,etc., etc. (ducks and runs..
) It also has giant panel gaps, it's made of plastic, and the interior is identical to a Cavalier. Also, people always say to me, "I never thought you were a Corvette guy!" 
Ah well, I like them both.
How about a super lightweight billet aluminum six piston caliper, similar to what an ALMS car would run...with matte black finish and laser-etched StopTech logo?
I've always liked the looks of the 350Z better. That said, my Z06 is actually quite a bit lighter than my 350 was...and it handles a lot better too...can use wider tires,etc., etc. (ducks and runs..
) It also has giant panel gaps, it's made of plastic, and the interior is identical to a Cavalier. Also, people always say to me, "I never thought you were a Corvette guy!" Ah well, I like them both.
How about a super lightweight billet aluminum six piston caliper, similar to what an ALMS car would run...with matte black finish and laser-etched StopTech logo?
That sounds like a bad *** brake dude....but actually i one upped the LS6
basically it is a cast iron LSX bow tie block stroked out to a 454 using a forged rotating assembly with 4" crank, 6" rods and 4.250 pistons...a 300 shot of the laughing gas....in a fully showable 350Z....it will be at sema...so if u wanna go for a ride afterwards just let me know!
08-24-2007, 01:08 PM
#47
Z + Rear Seat
iTrader: (3)
Join Date: Jun 2005
Location: St.Pete,FL
Posts: 1,642
Likes: 0
Received 0 Likes
on
0 Posts
How about a special edition spare tire/wheel that would fit over the giant rotors and calipers on most BBKs? I'll bet "losing your spare tire" stops a lot of people from getting a BBK.
Are the new calipers with piston sizes for a 2005 G35 Coupe ready for sale yet? How long would it take to get a set in Gold?
Are the new calipers with piston sizes for a 2005 G35 Coupe ready for sale yet? How long would it take to get a set in Gold?
08-24-2007, 07:09 PM
#48
I'm interested. Maybe have StopTech & Z below it in Silver. I don't know... throwing out ideas. lol
EDIT: Show read this post:
How much and where can I buy!?!?! Dooo eeet!!!
EDIT: Show read this post:
Originally Posted by J Ritt
How about a super lightweight billet aluminum six piston caliper, similar to what an ALMS car would run...with matte black finish and laser-etched StopTech logo?
How much and where can I buy!?!?! Dooo eeet!!!
Last edited by Robert_K; 08-24-2007 at 07:15 PM.
08-28-2007, 09:19 PM
#50
New Member
Thread Starter
iTrader: (4)
Join Date: Jun 2002
Location: Charlotte NC
Posts: 1,114
Likes: 0
Received 0 Likes
on
0 Posts
Haven't forgotten about this...just busy as usual! Stay tuned. We may have a special caliper coming soon. We're talking about debuting it at SEMA on a very special vehicle as well.
08-28-2007, 10:32 PM
#51
Originally Posted by J Ritt
Haven't forgotten about this...just busy as usual! Stay tuned. We may have a special caliper coming soon. We're talking about debuting it at SEMA on a very special vehicle as well.
Please keep me in the loop. I'm very interested in a SE, lighter bbk. I have now put my bbk purchase on hold till I see this release and specs.
08-29-2007, 09:37 AM
#52
Registered User
iTrader: (10)
Join Date: Dec 2003
Location: one of the 5 boros, NY
Posts: 2,704
Likes: 0
Received 0 Likes
on
0 Posts
i'll be at sema...does this mean my monster Z is getting a set?!? great thnx...
(noah continues to dream about getting special edition stop techs)
(noah continues to dream about getting special edition stop techs)
08-29-2007, 09:47 AM
#53
Originally Posted by NoahzBurnt
i'll be at sema...does this mean my monster Z is getting a set?!? great thnx...
(noah continues to dream about getting special edition stop techs)
(noah continues to dream about getting special edition stop techs)
NO!!! I'm getting the first kit!!! Cash in hand and waiting! LOLJeff,
Will this be a front & rear kit? sorry for the questions but I'm REALLY interested in this 6-pot billet aluminum, matte black, laser-etched kit.
08-29-2007, 09:55 AM
#54
Registered User
iTrader: (10)
Join Date: Dec 2003
Location: one of the 5 boros, NY
Posts: 2,704
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Robert_K
NO!!! I'm getting the first kit!!! Cash in hand and waiting! LOLJeff,
Will this be a front & rear kit? sorry for the questions but I'm REALLY interested in this 6-pot billet aluminum, matte black, laser-etched kit.
GET OUT OUT MY DREAMS ALREADY!!!!!!!
08-31-2007, 11:03 AM
#60
Originally Posted by Robert_K
Matte Black or Graphite color would be awesome!!!
Will