Lowering Springs Picture Thread
#61
Registered User
iTrader: (26)
Join Date: Jul 2008
Location: Baton Rouge
Posts: 6,084
Likes: 0
Received 0 Likes
on
0 Posts
You will have too much negative camber in the rear even without the springmount mod. It's not too bad with just springs but you will want to get it corrected when you start to see that camber wear.
#63
Registered User
iTrader: (28)
Join Date: Oct 2006
Location: ROFL
Posts: 3,258
Likes: 0
Received 0 Likes
on
0 Posts
I know every car is different, but I personally didn't have to purchase a rear camber kit. Well I did purchase it, but sold it because I ended up not needing one. If anything, my front tires wear faster than my rears.
#65
Registered User
iTrader: (5)
Join Date: Sep 2009
Location: Arlington
Posts: 119
Likes: 0
Received 0 Likes
on
0 Posts
hey guys what are the best springs to use that will let me keep my stock shocks and not use a camber kit? s-tech? i want a nice drop but not to an extreem because i have a STEEP driveway. i was between tein and prokit figure they dont even drop the car a full inch.
#67
Registered User
iTrader: (14)
Join Date: Dec 2007
Location: Ofallon, IL
Posts: 410
Likes: 0
Received 0 Likes
on
0 Posts
There's a sideview pic of mine in this thread:
https://my350z.com/forum/exterior-an...rom-paint.html
I'm on Eibach Sportlines
https://my350z.com/forum/exterior-an...rom-paint.html
I'm on Eibach Sportlines
#73
Registered User
2007 Touring - Tein S-Tech
I love the way it sits now .. not too low and should be able to get the alignment back in spec .. rides a little smoother on regular bumps yet is firmer around corners / doesn't drop or raise as much braking and accelerating
the sun threw a shadow on the wheels .. but you can make out where the top of the wheel is .. just follow the edge around .. I'll get a better pic when I wash it this week (car is dirty and just installed the springs last night)
I love the way it sits now .. not too low and should be able to get the alignment back in spec .. rides a little smoother on regular bumps yet is firmer around corners / doesn't drop or raise as much braking and accelerating
the sun threw a shadow on the wheels .. but you can make out where the top of the wheel is .. just follow the edge around .. I'll get a better pic when I wash it this week (car is dirty and just installed the springs last night)
#75
Registered User
iTrader: (19)
2007 Touring - Tein S-Tech
I love the way it sits now .. not too low and should be able to get the alignment back in spec .. rides a little smoother on regular bumps yet is firmer around corners / doesn't drop or raise as much braking and accelerating
the sun threw a shadow on the wheels .. but you can make out where the top of the wheel is .. just follow the edge around .. I'll get a better pic when I wash it this week (car is dirty and just installed the springs last night)
I love the way it sits now .. not too low and should be able to get the alignment back in spec .. rides a little smoother on regular bumps yet is firmer around corners / doesn't drop or raise as much braking and accelerating
the sun threw a shadow on the wheels .. but you can make out where the top of the wheel is .. just follow the edge around .. I'll get a better pic when I wash it this week (car is dirty and just installed the springs last night)
#76
New Member
iTrader: (7)
Alrighty, here's my set up:
Eibach Pro-Kit Springs
Tokico D-Spec Shocks
SPC Rear Camber/Toe Kit
Enkei RPF1 - Fr: 19x9 +18 w/245/35/19, Rr: 19x10 +22 w/275/35/19
Stock suspension to give an idea of where my Z started at:
Measurements (wheel center-ish to fender):
Passenger Front - 16-7/8"
Passenger Rear - 18"
Driver Front - 16-5/8"
Driver Rear - 17-3/4"
After (pics outside of garage are on uneven ground):
Measurement (wheel center-ish to fender):
Passenger Front - 16-1/4" (5/8" drop)
Passenger Rear - 16-7/8" (1-1/8" drop)
Driver Front - 16" (5/8" drop)
Driver Rear - 16-5/8" (1-1/8" drop)
Decently consistent drops front and rear. Will be measuring about 1x per week over the next two months to observe "settling", if any.
I suspect the height differences between driver vs. passenger sides might be due to the manufacturing tolerances of the sheet metal.
Alignment Specs:
Left Front..........................Right Front
-1.43°..........Camber.........-1.66°
7.76°...........Caster............7.51°
0.04°.............Toe..............0.03°
Left Rear..........................Right Rear
-1.60°..........Camber.........-1.62°
0.10°...........Caster............0.10°
Not as aggressive nor as low as some on these forums, but my Z is my DD and I needed it to be street friendly.
Just a special thanks to Steve and Nima at Corner3 Garage for their excellent work installing and helpful advising on selecting my set up.
Eibach Pro-Kit Springs
Tokico D-Spec Shocks
SPC Rear Camber/Toe Kit
Enkei RPF1 - Fr: 19x9 +18 w/245/35/19, Rr: 19x10 +22 w/275/35/19
Stock suspension to give an idea of where my Z started at:
Measurements (wheel center-ish to fender):
Passenger Front - 16-7/8"
Passenger Rear - 18"
Driver Front - 16-5/8"
Driver Rear - 17-3/4"
After (pics outside of garage are on uneven ground):
Measurement (wheel center-ish to fender):
Passenger Front - 16-1/4" (5/8" drop)
Passenger Rear - 16-7/8" (1-1/8" drop)
Driver Front - 16" (5/8" drop)
Driver Rear - 16-5/8" (1-1/8" drop)
Decently consistent drops front and rear. Will be measuring about 1x per week over the next two months to observe "settling", if any.
I suspect the height differences between driver vs. passenger sides might be due to the manufacturing tolerances of the sheet metal.
Alignment Specs:
Left Front..........................Right Front
-1.43°..........Camber.........-1.66°
7.76°...........Caster............7.51°
0.04°.............Toe..............0.03°
Left Rear..........................Right Rear
-1.60°..........Camber.........-1.62°
0.10°...........Caster............0.10°
Not as aggressive nor as low as some on these forums, but my Z is my DD and I needed it to be street friendly.
Just a special thanks to Steve and Nima at Corner3 Garage for their excellent work installing and helpful advising on selecting my set up.
Last edited by Anomaly; 09-21-2009 at 06:38 PM.