ATI Procharger 1/4 12.3 @ 112
#1
Registered User
Thread Starter
iTrader: (4)
Join Date: Dec 2003
Location: Annandale, VA
Posts: 1,635
Likes: 0
Received 0 Likes
on
0 Posts
ATI Procharger 1/4 12.3 @ 112
hey guys,
went to the track finally with the procharger, ran a 12.3 @ 112 and a 60' of 1.987 ...i was running the stock 17's and michelin pilot sport ps2's. Launched around 1.5krpms...pretty good night though 1st run of the night was a 12.8 @ 111 i beleive. Im happy, ill try and get a pic of the timesip but its near to impossible to see it when the flash goes off on the camera...ill try though
Ben Y
AAM
went to the track finally with the procharger, ran a 12.3 @ 112 and a 60' of 1.987 ...i was running the stock 17's and michelin pilot sport ps2's. Launched around 1.5krpms...pretty good night though 1st run of the night was a 12.8 @ 111 i beleive. Im happy, ill try and get a pic of the timesip but its near to impossible to see it when the flash goes off on the camera...ill try though
Ben Y
AAM
#5
Registered User
Thread Starter
iTrader: (4)
Join Date: Dec 2003
Location: Annandale, VA
Posts: 1,635
Likes: 0
Received 0 Likes
on
0 Posts
last dyno was 360
but ive added test pipes and a new plenum since then...so im thinking around 370ish??
ill have new numbers soon once the summer rolls around cause ill need a new tune job...btw im had no luck taking pics of the time slips...my flash just blurs the entire timeslip...and now the time slips are a good 4 hrs away from me...so when i get the chance ill post them up...
Ben Y
AAM
but ive added test pipes and a new plenum since then...so im thinking around 370ish??
ill have new numbers soon once the summer rolls around cause ill need a new tune job...btw im had no luck taking pics of the time slips...my flash just blurs the entire timeslip...and now the time slips are a good 4 hrs away from me...so when i get the chance ill post them up...
Ben Y
AAM
#6
Registered User
Join Date: Dec 2002
Location: Baltimore, MD
Posts: 323
Likes: 0
Received 0 Likes
on
0 Posts
Ben -
Still can't get over your 1/4 mile time....especially with the automatic and how slow it shifts (atleast mine does). I would only hope my car would run that quick, we'll see this summer. I 'll have to give you a run or two at the track, would be a good match-up, your car and mine. Later dude.
Aaron
Still can't get over your 1/4 mile time....especially with the automatic and how slow it shifts (atleast mine does). I would only hope my car would run that quick, we'll see this summer. I 'll have to give you a run or two at the track, would be a good match-up, your car and mine. Later dude.
Aaron
Trending Topics
#10
Registered User
Thread Starter
iTrader: (4)
Join Date: Dec 2003
Location: Annandale, VA
Posts: 1,635
Likes: 0
Received 0 Likes
on
0 Posts
i cant get a pic of the slip just yet...im in NYC and the slip is in VA...so when i get down there i will scan it or take a pic for you guys...i tryed before but the flash blurred everything and u can even see the printing...you just see a peice of paper...but they do make a torque converter and valve bodys for the Z, btw guys i was reving all the way up to 7500rpms....pretty high for a non built, no valve spring motor...it was pretty dangerous but i wasn't going to let off the throttle, i wanted a low time...going to see what i can for getting this time slip up on the net, ill try my best though,
Ben Y
AAM
Ben Y
AAM
Thread
Thread Starter
Forum
Replies
Last Post
Workshop12
Exterior & Interior
256
03-23-2020 01:45 PM
Bodyboarder81
Forced Induction
13
09-21-2015 06:23 AM