3.9 Final Drive - DIY Help
#21
Sponsor
Performance Nissan
Performance Nissan
iTrader: (11)
Join Date: Oct 2003
Location: So-Cal - Ready to go?
Posts: 8,783
Likes: 0
Received 2 Likes
on
2 Posts
NISSAN doesnt have a kit for it...
You need these adjust washers (shims) that are highlighted GREEN & RED
I put together a kit that includes all possible shims...
You need these adjust washers (shims) that are highlighted GREEN & RED
I put together a kit that includes all possible shims...
#25
Originally Posted by orangeboy
Pinion gear & ring gear $850
Central20 Final Drive seems considerably cheaper than the $850 quoted
http://www.z1auto.com/prodmore.asp?m...ne&prodid=1726
#28
Registered User
iTrader: (7)
Join Date: Dec 2006
Location: Florida
Posts: 260
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by orangeboy
So parts needed would be...
Pinion gear & ring gear $850
Side Bearing x2 $85
Side Bearing Oil Seal x2 $12
Drain Plug Washer x2 $3.90
Final Drive Gear Bolt x10 $20
Final Drive Side Gear Cir-clip x2 $1.40
Pinion Shaft Oil Seal $8.95
Pinion Shaft Crush Sleave $9.50
Pinion Nut $5
Front Pinion Bearing $34.95 (Item & price from 350evo's site)
Rear Pinion Bearing $54.95 (Item & price from 350evo's site)
Couldn't find the Front Pinion Bearing & Rear Pinion Bearing on PNP's website, I guess they can supply them OK or that I just missed them
So about $1085.65, plus whatever shims. Anything I've forgot? I'm asuming you can reuse all the driveshaft, halfshafts, & pumpkin nuts & bolts?
Pinion gear & ring gear $850
Side Bearing x2 $85
Side Bearing Oil Seal x2 $12
Drain Plug Washer x2 $3.90
Final Drive Gear Bolt x10 $20
Final Drive Side Gear Cir-clip x2 $1.40
Pinion Shaft Oil Seal $8.95
Pinion Shaft Crush Sleave $9.50
Pinion Nut $5
Front Pinion Bearing $34.95 (Item & price from 350evo's site)
Rear Pinion Bearing $54.95 (Item & price from 350evo's site)
Couldn't find the Front Pinion Bearing & Rear Pinion Bearing on PNP's website, I guess they can supply them OK or that I just missed them
So about $1085.65, plus whatever shims. Anything I've forgot? I'm asuming you can reuse all the driveshaft, halfshafts, & pumpkin nuts & bolts?
Hmm, i thought the ring and pinion sets where more like $500, not $800.
http://www.vividracing.com/catalog/p...ducts_id/20063 <<< $500...
#29
Registered User
iTrader: (4)
Join Date: Jun 2005
Location: Right Here
Posts: 248
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by scratch137
Hmm, i thought the ring and pinion sets where more like $500, not $800.
http://www.vividracing.com/catalog/p...ducts_id/20063 <<< $500...
http://www.vividracing.com/catalog/p...ducts_id/20063 <<< $500...
http://www.z1auto.com/prodmore.asp?m...ne&prodid=1726
Are there issues with the Central 20?
#30
Master
iTrader: (29)
DIY write up. Not our car, but a nice write up
Thought i would post this up. Its not our car, but it goes through the basic steps of what is needed and how to install the final drive.
http://www.pirate4x4.com/articles/te...sta/Gear_Setup
Hope this helps some
Later
Todd
http://www.pirate4x4.com/articles/te...sta/Gear_Setup
Hope this helps some
Later
Todd
#31
Registered User
iTrader: (19)
This is an old thread but I'll throw this in. Here is a great write up on a lsd and 3.9 final drive installation. It is in the DIY section. https://my350z.com/forum/engine-drivetrain-and-forced-induction-diy/233536-cusco-rs-and-3-9fd-install.html This should help out. The prices of 3.9 final drives are lower now because back when this thread was made I think there was only one company that made the 3.9 final drive. Now Central 20 is doing it and they are great and cheaper.
Thread
Thread Starter
Forum
Replies
Last Post