Rogue Engineering Short Shifter review
#1
New Member
Thread Starter
Join Date: Apr 2003
Location: Earth
Posts: 5,563
Likes: 0
Received 0 Likes
on
0 Posts
Rogue Engineering Short Shifter review
OK, during lunch today, I installed the Rogue Engineering short shifter. I've been driving it around for a couple hours since then.
Installation was very easy and the manual was very complete. There were no questions of what should go where, it covered everything. Installation is not difficult and can be accomplished with just a 10mm socket and a 12mm socket. They recommend you have a torque wrench available to torque the bolts to the proper level.
The hardest part about the installation was the removal of the control socket. I happen to have access to a hydraulic press so it took me like 5 seconds, but for those that don't it will be a little more difficult. The plastic holding the shifter arm in place is very stiff so you've really got to work at it. The rest of the installation was a piece of cake.
Driving the car with the new shifter is, let me be frank, f&%$ing awesome. The shifts are very smooth and require a tiny bit more force to get it into place, but the shorter throw more than makes up for that. I don't have anything to compare it to because I've never driven another car with a shifter like this. The gates are more precise and you know when it is in place, without a doubt.
There is no additional noise created by this shifter. It's just like a stock one, but you gotta move it less.
I thoroughly enjoy my shifter, thanks Rogue Engineering for building a great product. It was worth the wait.
Installation was very easy and the manual was very complete. There were no questions of what should go where, it covered everything. Installation is not difficult and can be accomplished with just a 10mm socket and a 12mm socket. They recommend you have a torque wrench available to torque the bolts to the proper level.
The hardest part about the installation was the removal of the control socket. I happen to have access to a hydraulic press so it took me like 5 seconds, but for those that don't it will be a little more difficult. The plastic holding the shifter arm in place is very stiff so you've really got to work at it. The rest of the installation was a piece of cake.
Driving the car with the new shifter is, let me be frank, f&%$ing awesome. The shifts are very smooth and require a tiny bit more force to get it into place, but the shorter throw more than makes up for that. I don't have anything to compare it to because I've never driven another car with a shifter like this. The gates are more precise and you know when it is in place, without a doubt.
There is no additional noise created by this shifter. It's just like a stock one, but you gotta move it less.
I thoroughly enjoy my shifter, thanks Rogue Engineering for building a great product. It was worth the wait.
#2
It is a great product. Unlike Jesseenglish, it took me about 20 minutes to get the control socket out. It's a b!tch, but it will eventually come out. Thanks Ben, great product, I love it.
#5
New Member
Thread Starter
Join Date: Apr 2003
Location: Earth
Posts: 5,563
Likes: 0
Received 0 Likes
on
0 Posts
LOL, I screwed mine up too. I was using the hydraulic press and was pushing the arm out the wrong way. It still works ok, because I stopped the press when I heard a cracking sound, but it could stand to be replaced.
#6
Registered User
iTrader: (1)
Easiest thing for removal is put it upside down between a vice or something similar.....but dont clap onto it.just let it hang down between the opening and then strike with a rubber hammer. it then pops right out.
I can check on pricing on these.i dont think they are that much. I know I have a brand new one in the shop.
I can check on pricing on these.i dont think they are that much. I know I have a brand new one in the shop.
#7
dwnshift,
thanks for the info.. I'll be trying the install it probably this weekend.. I'm a bit confused.. does the plastic part come out by downwards in relation to the shifter ****.. I'm a bit confused since you mentioned to turn it upside down and then strike the plastic piece..
I'm having problem visualizing the procedure.. could you help me out in understanding this better..
thanks for the info.. I'll be trying the install it probably this weekend.. I'm a bit confused.. does the plastic part come out by downwards in relation to the shifter ****.. I'm a bit confused since you mentioned to turn it upside down and then strike the plastic piece..
I'm having problem visualizing the procedure.. could you help me out in understanding this better..
Trending Topics
#12
Registered User
Join Date: Apr 2003
Location: Houston
Posts: 1,756
Likes: 0
Received 0 Likes
on
0 Posts
Do you really need to get under the car for this install like the directions mentioned? If so, what do i need to invest in so i can get under my car in the future? Thanx. 8-)
#13
New Member
Thread Starter
Join Date: Apr 2003
Location: Earth
Posts: 5,563
Likes: 0
Received 0 Likes
on
0 Posts
Yes, you've got to get your arm between the driveshaft and the car body. A good set of jackstands will make your life much easier. I used a lift, but not everyone has easy access to one.
#17
I am Batman
iTrader: (7)
Join Date: Aug 2003
Location: Northern Virginia
Posts: 1,867
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by dwnshift
.............. I smell 350EVO combo deal!
.............. I smell 350EVO combo deal!
#18
Registered User
Join Date: Jul 2002
Location: California
Posts: 535
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by dwnshift
I am running mine witha sparco bio blaclk handle with silver accents.
We have Nismo shifters in stock.............. I smell 350EVO combo deal!
I am running mine witha sparco bio blaclk handle with silver accents.
We have Nismo shifters in stock.............. I smell 350EVO combo deal!
Please show a pic of your handle along with your combo deal.
thanx
#19
Registered User
iTrader: (1)
I will try and get out to the shop tomorrow to take a picture.
If interested.....
I can work on a deal for the short shifter, either the sparco **** or Nismo ****'s and the plastic shifter cup.
Please email
BJ@350EVO.com
for that quote.
If interested.....
I can work on a deal for the short shifter, either the sparco **** or Nismo ****'s and the plastic shifter cup.
Please email
BJ@350EVO.com
for that quote.
#20
Registered User
Join Date: Jul 2002
Location: California
Posts: 535
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by dwnshift
I will try and get out to the shop tomorrow to take a picture.
If interested.....
I can work on a deal for the short shifter, either the sparco **** or Nismo ****'s and the plastic shifter cup.
Please email
BJ@350EVO.com
for that quote.
I will try and get out to the shop tomorrow to take a picture.
If interested.....
I can work on a deal for the short shifter, either the sparco **** or Nismo ****'s and the plastic shifter cup.
Please email
BJ@350EVO.com
for that quote.