DIY plenum porting
#242
Registered User
iTrader: (10)
Join Date: Jul 2003
Location: SoCal
Posts: 514
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by aleok
EK- that looks really good! did port and polish the intake manifold too? (the thing below plenum)
#244
Registered User
iTrader: (1)
Join Date: Nov 2005
Location: Honolulu
Posts: 352
Likes: 0
Received 0 Likes
on
0 Posts
heres come pics of what i've done so far, about $40 in dremel accessories! anyone have any suggestions b4 i put in back on? i'm also polishing up the upper plenum inside and out. will that cause it to run really hot? since its the roughness that supposedly keeps it cool?
sorry so big.
sorry so big.
#246
My350z
iTrader: (48)
ok guys, the lower plenum is going on tomorrow. i willl tune it using my utec and i will check my accelerometer and see if it pulls harder. i drive around alll the time and know the hardest it will pull in each gear with my best map on the utec.
updates tomorrow and i will take a few more pics of it after i got it back from the welding shop
if it works, it can all be done for about 125 at most from any shop that can weld aluminum. you will have to be able to tune it.
i hope my peak hp doesnt move off of my rpm range
updates tomorrow and i will take a few more pics of it after i got it back from the welding shop
if it works, it can all be done for about 125 at most from any shop that can weld aluminum. you will have to be able to tune it.
i hope my peak hp doesnt move off of my rpm range
#247
Registered User
iTrader: (1)
Join Date: Nov 2005
Location: Honolulu
Posts: 352
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by HyperSprite
Nice dog, he's really movin'
It's hard to tell from the pics whether it's really rough or just odd lighting.
I would get some 80 grit and just smooth things out a bit.
Chris
It's hard to tell from the pics whether it's really rough or just odd lighting.
I would get some 80 grit and just smooth things out a bit.
Chris
its pretty smooth, that with 120 grit. (i desided that the 60 grit left to make scratches that where not smooth.) its "smooth to the touch", it just has a lot of little "divites" that i created and it would take way more accessories and work to get them all out.
#248
Master
iTrader: (29)
Originally Posted by audiblemayhem
ok guys, the lower plenum is going on tomorrow. i willl tune it using my utec and i will check my accelerometer and see if it pulls harder. i drive around alll the time and know the hardest it will pull in each gear with my best map on the utec.
updates tomorrow and i will take a few more pics of it after i got it back from the welding shop
if it works, it can all be done for about 125 at most from any shop that can weld aluminum. you will have to be able to tune it.
i hope my peak hp doesnt move off of my rpm range
updates tomorrow and i will take a few more pics of it after i got it back from the welding shop
if it works, it can all be done for about 125 at most from any shop that can weld aluminum. you will have to be able to tune it.
i hope my peak hp doesnt move off of my rpm range
Exciting stuff going on
Later
Aceman
#249
MOTORDYNE-MY350Z SPONSOR
iTrader: (53)
Originally Posted by audiblemayhem
ok guys, the lower plenum is going on tomorrow. i willl tune it using my utec and i will check my accelerometer and see if it pulls harder. i drive around alll the time and know the hardest it will pull in each gear with my best map on the utec.
updates tomorrow and i will take a few more pics of it after i got it back from the welding shop
if it works, it can all be done for about 125 at most from any shop that can weld aluminum. you will have to be able to tune it.
i hope my peak hp doesnt move off of my rpm range
updates tomorrow and i will take a few more pics of it after i got it back from the welding shop
if it works, it can all be done for about 125 at most from any shop that can weld aluminum. you will have to be able to tune it.
i hope my peak hp doesnt move off of my rpm range
#255
New Member
iTrader: (2)
Join Date: May 2005
Location: Sin City
Posts: 175
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by audiblemayhem
ok guys, the lower plenum is going on tomorrow. i willl tune it using my utec and i will check my accelerometer and see if it pulls harder. i drive around alll the time and know the hardest it will pull in each gear with my best map on the utec.
updates tomorrow and i will take a few more pics of it after i got it back from the welding shop
if it works, it can all be done for about 125 at most from any shop that can weld aluminum. you will have to be able to tune it.
i hope my peak hp doesnt move off of my rpm range
updates tomorrow and i will take a few more pics of it after i got it back from the welding shop
if it works, it can all be done for about 125 at most from any shop that can weld aluminum. you will have to be able to tune it.
i hope my peak hp doesnt move off of my rpm range
any news on what happened when you put this back on
#257
Banned
iTrader: (2)
Join Date: Aug 2005
Location: OC - So Cal
Posts: 1,228
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Wired 24/7
You guys, I could be wrong about this but...
I get the feeling Tony is one to two steps ahead of the game.
Even if someone figures out the MREV 2 (which would not be very difficult), he probably has other ideas waiting to come out.
All he has to do is stay ahead of the competition, not to mention plastering his brand name to the point where competitors don't really stand a chance.
I get the feeling Tony is one to two steps ahead of the game.
Even if someone figures out the MREV 2 (which would not be very difficult), he probably has other ideas waiting to come out.
All he has to do is stay ahead of the competition, not to mention plastering his brand name to the point where competitors don't really stand a chance.