Sequential Rear LED Turn Signal Retro
oh also in the process in which you stated, does that mean the housing in which the buyer recieves will be that of the last person? if so does the condition of the housings not bother you, as one may be more damaged than anohters?
Originally Posted by creationv2
oh also in the process in which you stated, does that mean the housing in which the buyer recieves will be that of the last person? if so does the condition of the housings not bother you, as one may be more damaged than anohters?
As far as housing condition is concerned, yes that is an issue that will be addressed in the following manner. Whenever someone places an order for what ever configuration they wish, on top of the posted price, they will also need to place a deposit of $160. I will hold this deposit until I receive their housings. I will thoroughly clean and inspect both housings. After I have confirmed the housings are undamaged and acceptable, I will refund the deposit in full. If one wishes, they can just pay $160 for completely new housings. This price is not inflated, and is exactly the same as one would pay for a set of brand new housings with wiring harnesses included. I see this as the best way to handle the housing issue.
If there is any issue with a customer's housing, I will take it up with them through phone or private messages. If we can not both come to an agreement about how to handle the situation, then I will simply return the housings to them, and keep the deposit to purchase a new set.
Feel free to ask any more questions.
-Acree
Registered User
Joined: Mar 2005
Posts: 3,234
Likes: 0
From: Dallas Texas
Originally Posted by Acree
It does have to come all the way off. Here's a few basic steps:
1. Take out both tail light assemblies.
2. With a 10mm socket and atleast a 2" extension, take off the bolt that was under the tail light assembly. You will see it if you get down lower and look in the bottom corner. One on each side.
3. Unscrew one bolt on each bottom side of the bumper.
4. Unscrew one bolt on each side inside the fender well.
5. Get under the car and pop out the 2 retaining thingies.
6. Pull the passenger side out a little ways until you see the last retaining clip.
7. Put a small flathead screw drivers under the retaining clip between the body and the clip, NOT the bumper and the clip. There will be a clipping mechanism on opposing sides of the clip, so you need to push each one into the clip while pulling it out. Once you push in both sides, it will come out of the body.
8. CAREFULLY - Pull at the top part of the bumper between the 2 tail lights to pop lose the retaining clips.
9. Do the same to the clip on the driver's side.
10. Optional - Undo the wiring harness for the license plate lights, and both turn signal assemblies. You can take both turn signal assemblies out without unclipping the wiring harness from the license plate lights and leaving the bumper somewhat attached to the car.
11. On each housing, there are only 2 philips head screws on each side. Unscrew them and the housing will come out.
I will have a full step by step instruction set with pictures and steps that will ship with the turn signals. Hope this helps Hockey.
-Acree
1. Take out both tail light assemblies.
2. With a 10mm socket and atleast a 2" extension, take off the bolt that was under the tail light assembly. You will see it if you get down lower and look in the bottom corner. One on each side.
3. Unscrew one bolt on each bottom side of the bumper.
4. Unscrew one bolt on each side inside the fender well.
5. Get under the car and pop out the 2 retaining thingies.
6. Pull the passenger side out a little ways until you see the last retaining clip.
7. Put a small flathead screw drivers under the retaining clip between the body and the clip, NOT the bumper and the clip. There will be a clipping mechanism on opposing sides of the clip, so you need to push each one into the clip while pulling it out. Once you push in both sides, it will come out of the body.
8. CAREFULLY - Pull at the top part of the bumper between the 2 tail lights to pop lose the retaining clips.
9. Do the same to the clip on the driver's side.
10. Optional - Undo the wiring harness for the license plate lights, and both turn signal assemblies. You can take both turn signal assemblies out without unclipping the wiring harness from the license plate lights and leaving the bumper somewhat attached to the car.
11. On each housing, there are only 2 philips head screws on each side. Unscrew them and the housing will come out.
I will have a full step by step instruction set with pictures and steps that will ship with the turn signals. Hope this helps Hockey.
-Acree
awesome thanks for the answers acree....seems like a good and fair process....i think this is my last questions....model year should not matter right? as of now theyre all basically the same right? as in fitament, harnesses, etc?
and
how fast is the estimated turnover?
and
im not sure if acree would know this....but if anyone in socal can shed some light on whether lights like these would be illegal? jw cuz they are kind of distracting...
and
how fast is the estimated turnover?
and
im not sure if acree would know this....but if anyone in socal can shed some light on whether lights like these would be illegal? jw cuz they are kind of distracting...
Last edited by creationv2; Apr 19, 2006 at 12:46 PM.
Fitment, yes these will fit on any Z, 03-06. Everything will be strictly plug and play. Assuming I have a new set of housings on hand waiting to be converted, I will be able to complete a full set in 2-3 days.
-Acree
-Acree
thank you for answering all my questions
Registered User
Joined: Apr 2005
Posts: 65
Likes: 0
From: DFW, Texas
Just FYI courtesyparts.com sells the housing alone w/out the light bulbs for 54.99 each. That makes it much cheaper than the $160 a pair price.
http://www.courtesyparts.com/Merchan...de=26559-REVRS
http://www.courtesyparts.com/Merchan...de=26554-REVRS
http://www.courtesyparts.com/Merchan...de=26559-REVRS
http://www.courtesyparts.com/Merchan...de=26554-REVRS
Originally Posted by bghoward
Just FYI courtesyparts.com sells the housing alone w/out the light bulbs for 54.99 each. That makes it much cheaper than the $160 a pair price.
http://www.courtesyparts.com/Merchan...de=26559-REVRS
http://www.courtesyparts.com/Merchan...de=26554-REVRS
http://www.courtesyparts.com/Merchan...de=26559-REVRS
http://www.courtesyparts.com/Merchan...de=26554-REVRS
Ah good point BUT, for this conversion I have to use the housing with the harness. Those are $62.63 a piece. So once I buy 2 of them, I am looking at $125.26. Then once I add $10-15 bucks of shipping, I figured the extra $15-20 was more than fair for my time and effort in ordering new housings. I have been looking into using an aftermarket housing from ebay that has a completely clear housing. These housings are around $100 bucks. I might decide to offer these also.
Registered User
Joined: Mar 2006
Posts: 68
Likes: 0
From: Florida
Found these on E-bay, however Don't think they will work well for this application.
http://cgi.ebay.com/ebaymotors/04-05...72749788QQrdZ1
http://cgi.ebay.com/ebaymotors/03-06...3680QQrdZ1#des
http://cgi.ebay.com/ebaymotors/03-06...74758457QQrdZ1
http://cgi.ebay.com/ebaymotors/04-05...72749788QQrdZ1
http://cgi.ebay.com/ebaymotors/03-06...3680QQrdZ1#des
http://cgi.ebay.com/ebaymotors/03-06...74758457QQrdZ1
Last edited by zigggy56; Jun 12, 2006 at 07:34 AM.
Originally Posted by zigggy56
acree - Question nobody else on here has thought of... What is the flash pattern when you set the alarm throught the remote KeyFOB?
If your Z doesn't turn the signals on when you unlock the car, and does NOT honk when you lock it, hold down lock and unlock at the same time while you are near the car. This will change the mode to flash when unlocked, and flash/honk when locked. To change it back to the more quiet, lock only flash mode, just hold them down again.
-Acree
Last edited by Acree; Jun 15, 2006 at 06:16 AM.
Originally Posted by trescincuenta
OMG acree I searched all over for that because since day 1 my car never honked when arming and not event he manual says how to change it. Youre the man!
Very rarely do I laugh out loud while reading the forums, but that did it! I'm glad I could help man. -Acree