Autotecknic or Craft Square?
#161
New Member
iTrader: (17)
I posted a simple how to on how to tighten the ball joint on the mirror. It actually is a very simple thing, just use the allen key they gave you. Here is the link.
https://my350z.com/forum/exterior-and-interior/191118-autotechnic-cf-mirrors-loose-pivot-point.html
And unless you actually have a defective mirror or part, there is no reason to modify anything or use glue, etc. Properly set up the mirror should work like any other. Just understand the principals involved - the lenght of the inner threaded rod, how it pushes on the ball joint, etc. I guess that to save us $400 they cut out the guy who makes sure that every mirror has the rod tightened exactly right.
https://my350z.com/forum/exterior-and-interior/191118-autotechnic-cf-mirrors-loose-pivot-point.html
And unless you actually have a defective mirror or part, there is no reason to modify anything or use glue, etc. Properly set up the mirror should work like any other. Just understand the principals involved - the lenght of the inner threaded rod, how it pushes on the ball joint, etc. I guess that to save us $400 they cut out the guy who makes sure that every mirror has the rod tightened exactly right.
Last edited by gringott; 05-16-2006 at 07:55 AM.
#163
those ball stud joints are universal products.
the only thing autotecknic should be knocked for would be the way they poured the aluminum base and the cf mirror housing construction....
everything else, i bet would be the same pieces used by craftsquare since they're just normal hardware you can purchase from a catalog somewhere..
the only thing autotecknic should be knocked for would be the way they poured the aluminum base and the cf mirror housing construction....
everything else, i bet would be the same pieces used by craftsquare since they're just normal hardware you can purchase from a catalog somewhere..
#165
New Member
iTrader: (17)
Originally Posted by Chebosto
those ball stud joints are universal products.
the only thing autotecknic should be knocked for would be the way they poured the aluminum base and the cf mirror housing construction....
everything else, i bet would be the same pieces used by craftsquare since they're just normal hardware you can purchase from a catalog somewhere..
the only thing autotecknic should be knocked for would be the way they poured the aluminum base and the cf mirror housing construction....
everything else, i bet would be the same pieces used by craftsquare since they're just normal hardware you can purchase from a catalog somewhere..
#167
Registered User
iTrader: (6)
Join Date: Apr 2003
Location: 台灣屌
Posts: 1,134
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by gringott
I posted a simple how to on how to tighten the ball joint on the mirror. It actually is a very simple thing, just use the allen key they gave you. Here is the link.
https://my350z.com/forum/showthread.php?t=191118
And unless you actually have a defective mirror or part, there is no reason to modify anything or use glue, etc. Properly set up the mirror should work like any other. Just understand the principals involved - the lenght of the inner threaded rod, how it pushes on the ball joint, etc. I guess that to save us $400 they cut out the guy who makes sure that every mirror has the rod tightened exactly right.
https://my350z.com/forum/showthread.php?t=191118
And unless you actually have a defective mirror or part, there is no reason to modify anything or use glue, etc. Properly set up the mirror should work like any other. Just understand the principals involved - the lenght of the inner threaded rod, how it pushes on the ball joint, etc. I guess that to save us $400 they cut out the guy who makes sure that every mirror has the rod tightened exactly right.
Since most of the people who buys this mirror are putting it on themselves, I guess it wouldn't hurt to tighten the joint before installing!
#170
update.
i took my mirrors off to paint and to double check the stem length.
the stem is actually threaded about 3/4" deep, however, it is solid at the bend and not hollow, therefore you are limited to no more than 1/4" lowering/cutting off the top of the stem to reduce the height of the mirror and not have the bottom of the CF mirror interfere with the bend in the stem.
the base has some pits (due to the casting process) and can be filled using a slight application of bondo and doing a 250 grit sand, followed by a couple of passes of primer and a 400 wet sand..
i'll post picts of semi-gloss black paint when i'm completed..
i took my mirrors off to paint and to double check the stem length.
the stem is actually threaded about 3/4" deep, however, it is solid at the bend and not hollow, therefore you are limited to no more than 1/4" lowering/cutting off the top of the stem to reduce the height of the mirror and not have the bottom of the CF mirror interfere with the bend in the stem.
the base has some pits (due to the casting process) and can be filled using a slight application of bondo and doing a 250 grit sand, followed by a couple of passes of primer and a 400 wet sand..
i'll post picts of semi-gloss black paint when i'm completed..
#175
Originally Posted by INTENSEPOWER
Alan,
Thanks for your purchase. Your order shipped today. My Shipping Manager emailed you the tracking number a few minutes ago.. Thanks again. D.
Thanks for your purchase. Your order shipped today. My Shipping Manager emailed you the tracking number a few minutes ago.. Thanks again. D.
Darren,
Have mine shipped yet??
#176
Vendor - Former Vendor
iTrader: (208)
Join Date: Dec 2004
Location: Arizona
Posts: 2,038
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by NA&CH
Was there a price increase on these mirrors?
Yes, a couple of months ago. There's another thread floating around here that covers that subject. d
#177
Vendor - Former Vendor
iTrader: (208)
Join Date: Dec 2004
Location: Arizona
Posts: 2,038
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Alpha
Darren,
Have mine shipped yet??
Have mine shipped yet??
PM me your info plez. I'm assuming that you ordered black cf, as they have been on b/o for a minute now. Alan ordered silver cf, which we had 3 in stock. As far as the b/o being filled on the black cf, we were advised that they're on their way to us, and we should see 'em any day now. D.
#179
Registered User
iTrader: (3)
Join Date: Jul 2005
Location: Illinois
Posts: 416
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by INTENSEPOWER
Alan,
Thanks for your purchase. Your order shipped today. My Shipping Manager emailed you the tracking number a few minutes ago.. Thanks again. D.
Thanks for your purchase. Your order shipped today. My Shipping Manager emailed you the tracking number a few minutes ago.. Thanks again. D.