My clear corner install write-up
#22
Registered User
Thread Starter
iTrader: (7)
Join Date: Apr 2008
Location: Manassas, VA
Posts: 2,089
Likes: 0
Received 0 Likes
on
0 Posts
You may be able to feed them down there. I was figuring on the wires being attached to the corners and you having to feed them to the acc. circuit or however your hooking them up. Never-the-less, go ahead and follow my directions and look around and see if you can do it with out taking the bumper off. If you have to take it off, you’re already half way there anyway.
Last edited by 07rdsterGT; 06-03-2008 at 07:22 AM.
#23
Registered User
iTrader: (3)
Join Date: Jun 2005
Location: St. Petersburg, FL
Posts: 670
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by 07rdsterGT
You may be able to feed them down there. I was figuring on the wires being attached tot he corners and you having to feed them to the acc. circuit or however your hooking them up. Never-the-less, go ahead and follow my directions and look around and see if you can do it with out the bumper off. If you have to take it off, you’re already half way there anyway.
#29
Registered User
iTrader: (5)
Join Date: Feb 2008
Location: Farmington Hills, MI
Posts: 70
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by finalforce
Thanks for the info, I kind of stayed away from this mod because I didn't want to go through the hassle and take off the bumper. I'm now re-considering the idea of swapping to clears
#31
Banned
iTrader: (4)
Join Date: Dec 2006
Location: x
Posts: 2,171
Likes: 0
Received 0 Likes
on
0 Posts
I didn't remove my front bumper to change these either... Just used ramps to life my car enough for me to wiggle underneath- and stuck my arm between the wheel liner and the skid guard. The clear corners were very easy to remove and replace... it's a tight fit, but i have stick arms...if you have large arms and hands, this might not be the ideal way for you to do it.
#35
'12 TL SH-AWD
iTrader: (26)
Originally Posted by Z04
better than making a new thread and basically repeating what was done in a thread that was made two years ago then act like it was a new thing you discovered. good for you, you did one of the simplest mods that you can do for the Z.
https://my350z.com/forum/showpost.ph...7&postcount=50
and you even posted in that thread since it mentioned that you do not need to remover the bumper.
so basically repeating something that already exists is not contributing either.
https://my350z.com/forum/showpost.ph...7&postcount=50
and you even posted in that thread since it mentioned that you do not need to remover the bumper.
so basically repeating something that already exists is not contributing either.
Dude, STFU. His doesn't require you to take the bumper, wheel off which is a pain just to do reflectors. You DON'T need to do that. His is better than that two year old one you are recommending.
#40
Registered User
iTrader: (17)
Join Date: Jun 2007
Location: Irvine
Posts: 1,081
Likes: 0
Received 0 Likes
on
0 Posts
guys. chill out.
The more help from the community, the better is it for us.
There is no BEST way to install Clear corners... now we are open to 2 options. It is always better than 1.
The more help from the community, the better is it for us.
There is no BEST way to install Clear corners... now we are open to 2 options. It is always better than 1.