Need Hid Conversion Kit Suggestions
#42
Registered User
Thread Starter
Join Date: Aug 2008
Location: DMV
Posts: 62
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://my350z.com/forum/images/icons/icon1.gif)
Originally Posted by j1234
^^ prob one of the best kits to go with. i have his kit on my car. ballast hooks up to OEM location on 05 base.
#43
Registered User
iTrader: (5)
Join Date: Jul 2007
Location: NOLA
Posts: 1,523
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://my350z.com/forum/images/icons/icon1.gif)
install was pretty easy, i dont have any pics but if u search there are plenty, im sure JUN has some too. all i had to do was take off the front bumper, and headlights, screw the ballast to the bottom of the headlights drill a hole into the back cover of the headlight to run the wires through and plug it in, was simple
#44
Registered User
![Default](https://my350z.com/forum/images/icons/icon1.gif)
No probable retrofit in a projector type headlamp! Projector pattern directs light to the front causing no glare. This is an issue in open headlamps as in the Z hi-beam. Other point is HID quality, cheaper factories dont "align" (position) the bubble (center) of the bulb with the oem bulb, resulting in low light. Also dont pay much attention to exotic website and brand names, few factories sell all kit with different brands. Just those people put fancy boxes (some looks like jewel-boxes) with exotic cars and bike on it; and remember the box is for trash it...... Warranty is your best guide before any purchase. Thanks www.sagahid.com
#45
Charter Member #50
iTrader: (3)
Join Date: May 2002
Location: Houston, Texas
Posts: 3,552
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://my350z.com/forum/images/icons/icon1.gif)
Originally Posted by j1234
install was pretty easy, i dont have any pics but if u search there are plenty, im sure JUN has some too. all i had to do was take off the front bumper, and headlights, screw the ballast to the bottom of the headlights drill a hole into the back cover of the headlight to run the wires through and plug it in, was simple
I think Ace is looking for a direct plug-n-play deal..
#46
Registered User
Thread Starter
Join Date: Aug 2008
Location: DMV
Posts: 62
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://my350z.com/forum/images/icons/icon1.gif)
Originally Posted by Apexi350z
that doesn't sound too simple since you have to remove front bumper, screw the ballast to the headlights, and drill a hole.
I think Ace is looking for a direct plug-n-play deal..
I think Ace is looking for a direct plug-n-play deal..
Apexi350z I saw your install pics and lemme say...very NICE!
but the kit you got from DDM needed some wire splicing right? Would it be harder for me since I have a base version?
#47
Registered User
![Default](https://my350z.com/forum/images/icons/icon1.gif)
Ace, just remove the tire, the 4 clips that hold the liner and 2 screws below the bumper corner and Bingo!.....you get acces to the entire headlamp. From there you can change oem HID bulbs, add hi beam entire kit, replace parking light and turn signal for Leds. Very easy, I got everything you need if you want at www.sagahid.com Any other question you may send a pm. Thanks
#48
Charter Member #50
iTrader: (3)
Join Date: May 2002
Location: Houston, Texas
Posts: 3,552
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://my350z.com/forum/images/icons/icon1.gif)
Originally Posted by Ace07
Yea I'd like for the installation to be as simple as possible. Sam2944 how simple is your installation?
Apexi350z I saw your install pics and lemme say...very NICE!
but the kit you got from DDM needed some wire splicing right? Would it be harder for me since I have a base version?
Apexi350z I saw your install pics and lemme say...very NICE!
but the kit you got from DDM needed some wire splicing right? Would it be harder for me since I have a base version?
Once you cut the wires, you will have a RED & BLACK wire, and use those two to power the aftermarket HID kit.
** This is on my 03 Z with factory OEM HID ballast. Not sure if it's the same with Base non-HID wiring **
Last edited by Apexi350z; 09-08-2008 at 07:37 AM.
#49
Registered User
Thread Starter
Join Date: Aug 2008
Location: DMV
Posts: 62
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://my350z.com/forum/images/icons/icon1.gif)
Originally Posted by sam2944
Ace, just remove the tire, the 4 clips that hold the liner and 2 screws below the bumper corner and Bingo!.....you get acces to the entire headlamp. From there you can change oem HID bulbs, add hi beam entire kit, replace parking light and turn signal for Leds. Very easy, I got everything you need if you want at www.sagahid.com Any other question you may send a pm. Thanks
Thread
Thread Starter
Forum
Replies
Last Post
Lt_Ballzacki
Brakes & Suspension
39
08-06-2021 06:19 AM
2003, 2005, 350z, 35w, 5000k, 55w, apex, brightstar, conversion, factory, find, hid, kit, upgrading, wwwsagahidcom