G37S/Q60s 6Speed Transmisson Issue
#1
Registered User
Thread Starter
Join Date: Dec 2018
Location: Raleigh
Posts: 2
Likes: 0
Received 0 Likes
on
0 Posts
G37S/Q60s 6Speed Transmisson Issue
So I recently came across a problem in my 2014 Q60s 6speed. Never encountered this problem before & can’t find any information on my problem. PLEASE HELP.
If I am driving normally just cruising the car is fine. But if I decide to get into the car a lil banging gears the gears do not catch. For instance if I bang 2nd-3rd rarely would it catch a gear. The issue it does is get very loose. The car will not go into gear at all & if it does go into the gear it’s very very loose. In order to get it back to normal I have to press down as if I am going into reverse. Can someone please help me find my problem.
If I am driving normally just cruising the car is fine. But if I decide to get into the car a lil banging gears the gears do not catch. For instance if I bang 2nd-3rd rarely would it catch a gear. The issue it does is get very loose. The car will not go into gear at all & if it does go into the gear it’s very very loose. In order to get it back to normal I have to press down as if I am going into reverse. Can someone please help me find my problem.
#5
Master
iTrader: (5)
So I recently came across a problem in my 2014 Q60s 6speed. Never encountered this problem before & can’t find any information on my problem. PLEASE HELP.
If I am driving normally just cruising the car is fine. But if I decide to get into the car a lil banging gears the gears do not catch. For instance if I bang 2nd-3rd rarely would it catch a gear. The issue it does is get very loose. The car will not go into gear at all & if it does go into the gear it’s very very loose. In order to get it back to normal I have to press down as if I am going into reverse. Can someone please help me find my problem.
If I am driving normally just cruising the car is fine. But if I decide to get into the car a lil banging gears the gears do not catch. For instance if I bang 2nd-3rd rarely would it catch a gear. The issue it does is get very loose. The car will not go into gear at all & if it does go into the gear it’s very very loose. In order to get it back to normal I have to press down as if I am going into reverse. Can someone please help me find my problem.
What does "the issue it does is get very loose" mean?
How will either of these serve as feedback for the forum? (Since that's what sub forum you posted on).
#6
New Member
iTrader: (4)
Join Date: Feb 2005
Location: Get out my way pimpin, VA
Posts: 22,909
Received 2,446 Likes
on
1,768 Posts
The following users liked this post:
iideadeyeii (12-10-2018)
#7
350Z/370Z Tech Moderator
MY350Z.COM
MY350Z.COM
OK folks, please STOP. Let's not foster a hater environment (worse than it already is.)
OP, I would check your clutch. Doesn't seem to be disengaging fully/correctly under high speed load. If the clutch itself isn't at fault, very likely the hydraulic system isn't keeping up. Nissan never did quite fix the inherent CSC issue. Bad design.... or OK design, poor execution because the Z Speed HD replacement works fine.
OP, I would check your clutch. Doesn't seem to be disengaging fully/correctly under high speed load. If the clutch itself isn't at fault, very likely the hydraulic system isn't keeping up. Nissan never did quite fix the inherent CSC issue. Bad design.... or OK design, poor execution because the Z Speed HD replacement works fine.
Last edited by MicVelo; 12-07-2018 at 08:25 AM.
The following users liked this post:
rustyschopshop (12-10-2018)
Trending Topics
#8
******
iTrader: (1)
Stop driving like an idiot for starters.
The following users liked this post:
travlee (12-10-2018)
Thread
Thread Starter
Forum
Replies
Last Post