Again before people point fingers at me I have to say I HATE ON NO ONE, I just hate people getting ripped off by scums like VRT, so if shops have some unknown "Info X" that they're withholding, I think it's up to the good vendors to share their INFORMATION so people don't get fawked in the future.

If anyone wants to know about my chit I got my stuff done at Z Car Garage but will be getting all my work done (engine wise) by GTM in the future.

 

No, he is a male escort.does both male and female gigs.

 

+1

 

Go to this site and see if you can find me a set of Nismo Bearings,Nismo head studs, and Nismo main studs.
http://www.mynismo.com/

 

Some ethical ?'s were raised about the shop you are choosing to do the work . The ?'s were quickly squashed when the thread was closed and or deleted . Do you know about that ? And are you ok with it ?

 

I'm the G35 rock star of NJ, he just has the faster car.

 

what thread are you referring to? the only threads that got locked or deleted here are AAM's.

 

Maybe it wasnt deleted , but closed for sure . It was the thread about the BuiltZMotors....motor ...that Sam talked the owner into tearing down . IMPO...un-ethical to the max...and all for the $$$$$$$

 

^ I remember that thread. I think it was closed per the OP's asking IIRC since the situation was resolved.

also, Helldorado is such a rockstar. he's got the hair and the attitude

 

I see what you're getting into. Julian, I take it that as time goes by info will be leaked. I only hope that good people and bad people get what they deserve. I don't hate on anyone or any shops and I DON'T KNOW if people are lying or not but I hate the likes of VRT and liars and thieves.

I hope ALL con artists become exposed.

 

^Didn't see that one coming.

...

...

...

...

Sooooo...

Let's stop beating around the bush please. Based on the above posts, am I correct in assuming that Sharif got an engine which RA built that supposedly has an invoice for parts that either don't exist or were not actually included in the received engine?

 

Sam has always been a curteous guy towards me and all of their products are top-notch. They are also in the West Coast and close to me (relatively speaking). Sure they might not be perfect, but if they choose to take care of customers and of course NOT rip people off then it's fine with me, we are all human after all.

 

Didn't see that one coming either

someone needs to confirm this...if true

 

Ot

 

Okie dokie. Fixed.

 

are you correct on this one too?


lol

 

no, because combat likes chubby little boys

 

As i predicted last week via Philthy's useless rantings, you got yourself sucked into drama. You could not even factually explain yourself or your confusing accusations if i put a thousand dollars in front of you. This smells like a smear campaign. With nothing to prove any wrongdoings by R.A.
I think it is "Due Time" as you say... for the "truth" to come out... the same exact words you used were used by Philthy last week. And if it doesn't come out real soon you crap talkers should be the ones worrying about your reputations. Your rhetoric is weak and baseless.... all three of you.

 

Sharif, regarding the paper work on that motor build you are referring to, i spoke
to Scott last week about it.... that's how old this is folks. A week old.
The paperwork that went with the motor was in fact a clerical error by the company that delivered the motor. I also understand that YOU are also aware of this fact, but instead you are choosing to use it as misinformation to hurt R.A.
The issue was cleared up immediately and the customer understood the paperwork error. Please explain yourself? Thank you.

 

LOL...this is going to get interesting really fast. Hang tight folks. No paperwork came with the engine...it came from the customer via fax.

This really is going to be VRT all over again....but in a different thread...NOT this one.