Eagletanggreen >>>> I Blew my Motor Today!!<<<<
03-11-2008, 03:06 PM
#143
Got Track!!!!!
Thread Starter
iTrader: (40)
Join Date: May 2005
Location: Fayetteville, NC
Posts: 3,307
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by SpoilsofWar
Wow...
Any damage to those valves?
Any damage to those valves?
I put it all back together went for a drive on high boost with meth and 110 and ripped 4th @ around 4500rpms.. Ahh! NO valves are fine
03-11-2008, 03:11 PM
#146
Originally Posted by eagletanggreen
I put it all back together went for a drive on high boost with meth and 110 and ripped 4th @ around 4500rpms.. Ahh! NO valves are fine
03-11-2008, 03:15 PM
#147
Got Track!!!!!
Thread Starter
iTrader: (40)
Join Date: May 2005
Location: Fayetteville, NC
Posts: 3,307
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Philthy
I hope everything is 100%, but you said the same thing when you had a piece of metal slapping against your valves... I would take it easy until you do some more testing, change fluids, check the oil, compression test, etc...
Yeah I will. I did change the oil and everything looked good no metal shaving or crazy thing. I used peice of screen to go thru the oil. Compression test would do the trick.
03-11-2008, 04:02 PM
#148
Professional
iTrader: (2)
Join Date: Jan 2006
Location: Virginia
Posts: 4,398
Likes: 0
Received 0 Likes
on
0 Posts
I hope it's not to bad and everything checks out.
I have to admit though...I love your diagnostics technique. lol
Just ripped thru 4th with 110 in it, on high boost, and meth..... lol You got more ***** than me.
You are a lucky SOB. but im sure some (hopefully minimal) damage was done unfortunately.
I have to admit though...I love your diagnostics technique. lol
Just ripped thru 4th with 110 in it, on high boost, and meth..... lol You got more ***** than me.
You are a lucky SOB. but im sure some (hopefully minimal) damage was done unfortunately.
03-11-2008, 05:34 PM
#151
The piece could have not done any damage. Lucky for him it didnt keep the valve from closing, bend it, enter the cylinder, etc. I would change the oil (remember to send it out for analysis Luie!!!!), motor is most likely fine, if it did do damage he would know it by now. Some people are overly "concerned". Luie you def have a horseshoe up your a$$ you lucky ****!
03-11-2008, 05:52 PM
#152
Got Track!!!!!
Thread Starter
iTrader: (40)
Join Date: May 2005
Location: Fayetteville, NC
Posts: 3,307
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Alberto
The piece could have not done any damage. Lucky for him it didnt keep the valve from closing, bend it, enter the cylinder, etc. I would change the oil (remember to send it out for analysis Luie!!!!), motor is most likely fine, if it did do damage he would know it by now. Some people are overly "concerned". Luie you def have a horseshoe up your a$$ you lucky ****!
Yeah sent Joe some details pics of the Valve in question and he said the piece was to big to get into the motor. He said with my cams those valves open about a half of an inch so there was no way to get in there the valvle looks nice and sealed and completely closed. She pull hard no clicking noises at low or high rpm, and she pulls like a raped ape.
Thats two close calls.... No more raping my car till myself, Joe and Alberto have our cook out. So you wont be seeing anymore times from me anytime soon.
But when you have what happen to me this weekend and then find a chunk of metal in your car.... Well...... Thank You baby Jesus for sparing my car!
I promise I will be good for a while. ... Luie!
03-11-2008, 05:57 PM
#154
Got Track!!!!!
Thread Starter
iTrader: (40)
Join Date: May 2005
Location: Fayetteville, NC
Posts: 3,307
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Alberto
LOL Im hungry, cant wait for the cookout! Yellow Z with supertranny will do the trick
03-11-2008, 06:00 PM
#156
Banned
iTrader: (28)
Join Date: Dec 2005
Location: Spotswood NJ
Posts: 5,510
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by eagletanggreen
Yeah sent Joe some details pics of the Valve in question and he said the piece was to big to get into the motor. He said with my cams those valves open about a half of an inch so there was no way to get in there the valvle looks nice and sealed and completely closed. She pull hard no clicking noises at low or high rpm, and she pulls like a raped ape.
Thats two close calls.... No more raping my car till myself, Joe and Alberto have our cook out. So you wont be seeing anymore times from me anytime soon.
But when you have what happen to me this weekend and then find a chunk of metal in your car.... Well...... Thank You baby Jesus for sparing my car!
I promise I will be good for a while. ... Luie!
Thats two close calls.... No more raping my car till myself, Joe and Alberto have our cook out. So you wont be seeing anymore times from me anytime soon.
But when you have what happen to me this weekend and then find a chunk of metal in your car.... Well...... Thank You baby Jesus for sparing my car!
I promise I will be good for a while. ... Luie!
We had one bend the trottle blades and blow out the intake tube and front headlight..
03-11-2008, 06:01 PM
#157
Got Track!!!!!
Thread Starter
iTrader: (40)
Join Date: May 2005
Location: Fayetteville, NC
Posts: 3,307
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Julian@MRC
Your lucky that Nitrous Backfire didnt do worse damage.. We had one bend the trottle blades and blow out the intake tube and front headlight..
We had one bend the trottle blades and blow out the intake tube and front headlight..Dude! Dont make go out there and check my blades
Oh well I have a back up in the garage
03-11-2008, 06:03 PM
#159
Banned
iTrader: (28)
Join Date: Dec 2005
Location: Spotswood NJ
Posts: 5,510
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Alberto
Whats with the N20 talk, you dont think a 675whp can trap 133mph spinning Julian?
03-11-2008, 06:12 PM
#160
Registered User
iTrader: (3)
Join Date: Jun 2005
Location: Indianapolis, IN
Posts: 423
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Alberto
By the top of 4th my meal is over
