Vinny Ten Racing: JWTT 625whp pump gas 17psi
#21
New Member
iTrader: (44)
this VTR is kind of expensive vs most you can get a built engine to hold up to that power level for cheaper. not going to talk bad about VTR though they are one of only a couple shops ive never heard of having engine problems. if i couldnt do it myself i wouldnt be scared to take it to them and one other. plenty of people with no problems just stick around awhile, alot of people just dont have built threads.
what jeff said about the no blown engines i believe is why we dont hear much from VTR lol but like i said they are a bit more then other places
also good luck with the 2JZ, even at just 700 and not building the engine looking at probably 6-10k...................plus at least that probably double that for install, plus materials for fabrication and all the other **** you will need. if you want a full built engine look at 8k just for a stroker kit.
what jeff said about the no blown engines i believe is why we dont hear much from VTR lol but like i said they are a bit more then other places
also good luck with the 2JZ, even at just 700 and not building the engine looking at probably 6-10k...................plus at least that probably double that for install, plus materials for fabrication and all the other **** you will need. if you want a full built engine look at 8k just for a stroker kit.
#22
Registered User
iTrader: (4)
yah i dint figure engine cost in, i dont want even to know what you have invested lol
2jz and 5spd is what, 3-3500 alone. 2jz and 6spd 6-7k alone and that is just for engine and trans. If you are looking to save money don't even consider a 2jz swap. Plenty of pros but cons as well. But let's not get too off topic, you're still spending a lot to build a TT Z the right way. Wish I would see this Z in NJ. Have been wanting to for awhile now. Good luck with it.
#24
New Member
iTrader: (8)
Join Date: Jan 2007
Location: terre haute, IN; STL, MO
Posts: 6,457
Likes: 0
Received 7 Likes
on
6 Posts
i watched a few track videos and some other dynos of this car. What did it run on pump gas? I saw the 10.54 on race gas (over 700hp dyno vid) so i assume the 10.3 was on race gas as well unless vinny ten was incorrect in his video about it being raced on race gas.
#28
Registered User
iTrader: (6)
Join Date: May 2009
Location: Lubbock, Tx
Posts: 267
Likes: 0
Received 0 Likes
on
0 Posts
PARTS:
CUSTOM SLEEVED DARTON BLOCK
VTR ARP H STUDS ½-13
VTR CP PISTONS W/866 & L.G.P.
VTR TOTAL SEAL RINGS
ARP MAIN STUD KIT
ACL/CALICO MAIN BEARINGS
ACL/CALICO ROD BEARINGS
NISSAN THRUST WASH
GTR SKYLINE FACTORY HEAD
CARRILLO H BEAMS W/WMC BOLTS
MACHINE WORK
CNC INSTALL MID KIT
DRILL & TAP 1/2-13 H-BOLT HOLES
DECK SURFACE OF BLOCK
HAND FINISH DECK TO # 50 RA
POWER HONE WITH PLATE
LINE HONE
MICRO POLISH RADIUS OIL HOLES
REMOVE GALLEY *****, FLUSH CLEAN
DRILL & TAP FOR SET SCREWS
RESIZE RODS FOR ADDITIONAL CLEARANCE
BALANCE COMPLETE ROTATING ASSEMBLY
FILE FIT RING TO BORE
you guys are putting GTR heads on it???
CUSTOM SLEEVED DARTON BLOCK
VTR ARP H STUDS ½-13
VTR CP PISTONS W/866 & L.G.P.
VTR TOTAL SEAL RINGS
ARP MAIN STUD KIT
ACL/CALICO MAIN BEARINGS
ACL/CALICO ROD BEARINGS
NISSAN THRUST WASH
GTR SKYLINE FACTORY HEAD
CARRILLO H BEAMS W/WMC BOLTS
MACHINE WORK
CNC INSTALL MID KIT
DRILL & TAP 1/2-13 H-BOLT HOLES
DECK SURFACE OF BLOCK
HAND FINISH DECK TO # 50 RA
POWER HONE WITH PLATE
LINE HONE
MICRO POLISH RADIUS OIL HOLES
REMOVE GALLEY *****, FLUSH CLEAN
DRILL & TAP FOR SET SCREWS
RESIZE RODS FOR ADDITIONAL CLEARANCE
BALANCE COMPLETE ROTATING ASSEMBLY
FILE FIT RING TO BORE
you guys are putting GTR heads on it???
#29
でたらめ検出器
iTrader: (1)
PARTS:
CUSTOM SLEEVED DARTON BLOCK
VTR ARP H STUDS ½-13
VTR CP PISTONS W/866 & L.G.P.
VTR TOTAL SEAL RINGS
ARP MAIN STUD KIT
ACL/CALICO MAIN BEARINGS
ACL/CALICO ROD BEARINGS
NISSAN THRUST WASH
GTR SKYLINE FACTORY HEAD
CARRILLO H BEAMS W/WMC BOLTS
MACHINE WORK
CNC INSTALL MID KIT
DRILL & TAP 1/2-13 H-BOLT HOLES
DECK SURFACE OF BLOCK
HAND FINISH DECK TO # 50 RA
POWER HONE WITH PLATE
LINE HONE
MICRO POLISH RADIUS OIL HOLES
REMOVE GALLEY *****, FLUSH CLEAN
DRILL & TAP FOR SET SCREWS
RESIZE RODS FOR ADDITIONAL CLEARANCE
BALANCE COMPLETE ROTATING ASSEMBLY
FILE FIT RING TO BORE
you guys are putting GTR heads on it???
CUSTOM SLEEVED DARTON BLOCK
VTR ARP H STUDS ½-13
VTR CP PISTONS W/866 & L.G.P.
VTR TOTAL SEAL RINGS
ARP MAIN STUD KIT
ACL/CALICO MAIN BEARINGS
ACL/CALICO ROD BEARINGS
NISSAN THRUST WASH
GTR SKYLINE FACTORY HEAD
CARRILLO H BEAMS W/WMC BOLTS
MACHINE WORK
CNC INSTALL MID KIT
DRILL & TAP 1/2-13 H-BOLT HOLES
DECK SURFACE OF BLOCK
HAND FINISH DECK TO # 50 RA
POWER HONE WITH PLATE
LINE HONE
MICRO POLISH RADIUS OIL HOLES
REMOVE GALLEY *****, FLUSH CLEAN
DRILL & TAP FOR SET SCREWS
RESIZE RODS FOR ADDITIONAL CLEARANCE
BALANCE COMPLETE ROTATING ASSEMBLY
FILE FIT RING TO BORE
you guys are putting GTR heads on it???
http://vinnytenracing.com/engine/the...longblock.html
#40
New Member
iTrader: (10)
If i nail the 60, car will fall right into the nines the mph is there . The 850's produce some instant torque in first, so it seems I need to calm the car down a bit in first. The car is very consistent and that's all I can ask for.