Tanabe Medallion + Berk HFC
#23
Super Moderator
MY350Z.COM
MY350Z.COM
iTrader: (8)
Well i didn't run HFC's on mine i ran resonated test pipes. Sounded great, still quiet, not raspy and completely different than a Nismo with test pipes.
#24
New Member
iTrader: (9)
im not positive but pretty sure they are the same design and the tanabe is a knockoff of the nismo design...looks like the tanabe is the same design to me but idk..ive heard of people using the tanabe mid pipe and all on a nismo cat back
http://cgi.ebay.com/ebaymotors/TANAB...Q5fAccessories
^look at the design
http://ep.yimg.com/ca/I/phase2motors...2091_257238120
http://cgi.ebay.com/ebaymotors/TANAB...Q5fAccessories
^look at the design
http://ep.yimg.com/ca/I/phase2motors...2091_257238120
#26
New Member
iTrader: (6)
so essentially you want a 60 mm HFC to use with the T y pipe. If Berk is in fact 60 mm (2.36) then you will have zero issue with flow. If they (Berk HFC's) are 2.5 i'm not sure what to expect since the stock headers are closer to 2.36 if not 2.36
essentially a good Tanabe setup would be as follows!
HFC's or test pipes of ur choice 60mm - Tanabe Y pipe = 60mm merges to 70 mm -Tanabe mid pipe = 70 mm - exhaust inlet = 70 mm
#28
Super Moderator
MY350Z.COM
MY350Z.COM
iTrader: (8)
Sound clips, never have and never will post them. They never sound the same as in person.
#29
Registered User
iTrader: (15)
dude ur thinking too much into it...just get the berk high flow cats if u want high flows and put them on, u wont have rasp with that setup, and if by some slight chance u do get rasp or want it deeper and cleaner get the motordyne xyz w/ resonator..the motordyne xyz is the best y pipe money can buy and worth every penny, i love mine, i dont rasp with berk test pipes with my xyz w/ resonator and nismo mid and tail section but had rasp with my normal nismo y pipe
#34
Registered User
I got a question about the pipping size of the berk HFC... i have AAM y-pipe and it is 2.5" and goes to 3"... The berk HFC are 2.36". Would there be any problems with this setup?
#35
Registered User
iTrader: (12)
Join Date: Sep 2007
Location: San Antonio,Tx
Posts: 2,167
Likes: 0
Received 0 Likes
on
0 Posts
i use to have this tanabe exhaust and man did it sound great, i had kinetix hfc's and a motordyne y-pipe. The sound of it was amazing and made great power, never got to get a sound clip of it , maybe i could get one from my friend cause i sold it to him.
#36
^
Yeah if you could do that I'd appreciate it. Did you experience any hiss from the hfc's with your set up that you recall?
For now im Im going to use the stock Y-pipe until i can find a used aftermarket or HR Y-pipe.
Im sure the hfc's increased the decibal level a bit huh?
How was the drone?
Yeah if you could do that I'd appreciate it. Did you experience any hiss from the hfc's with your set up that you recall?
For now im Im going to use the stock Y-pipe until i can find a used aftermarket or HR Y-pipe.
Im sure the hfc's increased the decibal level a bit huh?
How was the drone?
#37
New Member
iTrader: (4)
While I don't have the Touring edition I have the Tanabe Hyper Medallion. I have it matched up with the Tanabe Y-Pipe and the Berk HFC's. The HFC's matched up just fine to the Stock & Tanabe Y-Pipe. The HFC's do provide some hiss and they also produce very little rasp when WOT. The exhaust note is loud enough to phase out the rasp. Overall its an amazing sounding exhaust.
#38
While I don't have the Touring edition I have the Tanabe Hyper Medallion. I have it matched up with the Tanabe Y-Pipe and the Berk HFC's. The HFC's matched up just fine to the Stock & Tanabe Y-Pipe. The HFC's do provide some hiss and they also produce very little rasp when WOT. The exhaust note is loud enough to phase out the rasp. Overall its an amazing sounding exhaust.
Did the car have any studder after the hfc install?
#39
Registered User
iTrader: (12)
Join Date: Sep 2007
Location: San Antonio,Tx
Posts: 2,167
Likes: 0
Received 0 Likes
on
0 Posts
^
yeah if you could do that i'd appreciate it. Did you experience any hiss from the hfc's with your set up that you recall?
For now im im going to use the stock y-pipe until i can find a used aftermarket or hr y-pipe.
Im sure the hfc's increased the decibal level a bit huh?
How was the drone?
yeah if you could do that i'd appreciate it. Did you experience any hiss from the hfc's with your set up that you recall?
For now im im going to use the stock y-pipe until i can find a used aftermarket or hr y-pipe.
Im sure the hfc's increased the decibal level a bit huh?
How was the drone?
#40
Ha ha ha..
So I went to go attempt to put this on with only two ramps.
Taking the oem rear section off with no room is a *****. I get that off and I hadn't looked at the midpipe to compare. The oem did not mate up with the Tanabe...argh.
I was putting it on temporarily because my buddy(with proper tools bailed).
After spending about 2 hours wrestling with the rubber hangers removing the oem, I had to put it back since I didnt have clearance to reach mid-pipe.
I had to laugh..
So I went to go attempt to put this on with only two ramps.
Taking the oem rear section off with no room is a *****. I get that off and I hadn't looked at the midpipe to compare. The oem did not mate up with the Tanabe...argh.
I was putting it on temporarily because my buddy(with proper tools bailed).
After spending about 2 hours wrestling with the rubber hangers removing the oem, I had to put it back since I didnt have clearance to reach mid-pipe.
I had to laugh..